Top 20 GE WSXH208A Front Load Washer Questions & Answers


We need the exact model number,

GE WSXH208A... | 660 views | 0 helpful votes


please go to the website and download the user guide to give you an idea whats going wrong eric

GE WSXH208A... | 70 views | 0 helpful votes


Please, check to insure that your washer is properly grounded. If you do not know what that means, call an electrician. Modern wash machines are controlled by circuit boards that operate on low voltage and are vulnerable to static electricity. Spikes or gaps in the electrical service from your power company could also be the problem. Your electrician should be able to help you with that as well.

GE WSXH208A... | 399 views | 0 helpful votes


Front loaders frequently suffer bearing failure.

GE WSXH208A... | 737 views | 0 helpful votes


Could be. The instruction manual could provide guidance. Sometimes manufacturers are very specific about what to use and how to use it.

GE WSXH208A... | 54 views | 0 helpful votes


Might be a leaky solenoid

GE WSXH208A... | 89 views | 0 helpful votes


It is a circuit so test the connections on the washer side.... insert a lead into one and a lead into the other... repeat until you get the correct two... right 2 will give you a reading the wrong ones nothing

GE WSXH208A... | 197 views | 0 helpful votes


Sorry You 'll have to remove the dryer to allow access to the washer's inner components. It takes two but the dryer isn't that heavy.

GE WSXH208A... | 49 views | 0 helpful votes


may be some thing in drain pump

GE WSXH208A... | 80 views | 0 helpful votes


No spin, try these:
Using a multi meter check for continuity the door switch, which when bad may not allow agitation or spin. The lid switch assembly can fail either mechanically or electrically.

Check the clutch, brake assembly and transmission, one way to check for slipping is to get under the machine after a spin cycle ( this is if u get a lil spin but not much leaving clothes still wet) mix in a spray bottle a lil water and some dish detergent, then spray it on the clutch assembly ( the metal round pc. Connected to the tranny) if it sizzles and steams up then u know its bad and slipping. Another way to check clutch if u get no spin at all? Is to take it out and use ur hand to try and turn the inner spring assembly pushing it around the inside? If its very easy, it BAD should be hard to push by hand.


Next check the motor coupler which engages the tub and tranny to the motor. ( if its bad u usually get no wash or spin or very little of either)

Next check for a loose, worn or broken belt if belt driven.

On some front load models u may need to check the STATOR assembly.
The stator is essentially one half of a motor, it interacts with the tub by creating a strong electro-magnet. If the stator burns out the washer won't spin or agitate. Check the stator for continuity. This part is often misdiagnosed.


GE WSXH208A... | 87 views | 0 helpful votes


Out of ballance. Distribute clothes evenly.

GE WSXH208A... | 48 views | 0 helpful votes


google details for model you may find factory removal instructions.

GE WSXH208A... | 44 views | 0 helpful votes


Check the door switch..Most washers won't drain or spin if the switch is not closed. It could be loose. Look for two small screws on the side opposite the door hinges and make sure they are tight. you can also try depressing the switch with a screwdriver with the door open. If it works, the switch is good it's just loose. If it doesn't you probably need a new switch.

GE WSXH208A... | 55 views | 0 helpful votes


If the drain motor filter is cleared out and still not working then you are going to need to replace the motor in your front loading washer I had lightening strike near my home once and although it would still adgitate it would not spin properly or even adgitate properly After having service men come out a number of times I ended up replacing almost every part including the motor which finally fixed the problem

GE WSXH208A... | 81 views | 0 helpful votes


It can be a bad door lock or Check out the lid switch by testing it for continuity. If it is not working correctly change it out, here is the part.

Read more: http://forum.appliancepartspros.com/washer-repair/102406-top-load-washer-wont-go-into-spin-cycle.html#ixzz31O0yhLXE
http://forum.appliancepartspros.com

GE WSXH208A... | 39 views | 0 helpful votes


take bottom cover off and check to see if the drain hose running from the pump is leaking also check the pump sometimes they crack causing a leak

GE WSXH208A... | 72 views | 0 helpful votes


need to check the hose from the pump also pump could be cracked causing leak

GE WSXH208A... | 59 views | 0 helpful votes

Not finding what you are looking for?
GE WSXH208A Front Load Washer Logo

1,215 questions posted

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

geapptech

Level 2 Expert

157 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GE Washing Machines

  • GE Washing Machines

Most Popular Question

ge front load washer wont start model

  • Washing Machines
Loading...