20 Most Recent Minolta CF2001 Copier Questions & Answers


how the code appeared?
I suppose you worked with the cyan low toner attention untill the machine stopped. in this case you should make an ATDC sensor adjustement! but firstly you should reset the error!

Minolta CF2001... | Answered on Nov 28, 2016


well the fuser motor is jammed. remove the fuser and replace it. hopefully the motor is not burned out, and or worse the motor took the control board also

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta CF2001... | Answered on Nov 21, 2015


go to admin mode net work settings.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta CF2001... | Answered on Nov 14, 2015


Order new fusing unit cant gets small parts. try this site for parts


Precision Roller Printer Toner Cartridges Parts and Supplies Office...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta CF2001... | Answered on Mar 02, 2015


open the front door get down on the floor look up at the slant section right side will see a small hole you will not see it standing up get a small, small screwdriver push the button inside the hole to hit the reset switch. if the code comes back replace the FUSING UNIT the hot part. worse case the control board is bad$$$$$$. Do not continue to reset it can catch on fire and that would ruin a perfectly good day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta CF2001... | Answered on Feb 20, 2015


Unit is located above the fusing unit (The Hot Part)

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta CF2001... | Answered on Feb 20, 2015


What to do or the part number or the what do you need? When printing or copying? which draw are you using double sided or single?

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta CF2001... | Answered on Feb 04, 2015


Clean the optical parts and the charge and discharging coronas.

Minolta CF2001... | Answered on Jan 12, 2014


Hold utility down when switching on for 20 sec trouble reset should appear. Click ok then reboot. If code returns engineer required.

Minolta CF2001... | Answered on Oct 20, 2013


SOLUTION: Check the amount of toner in the affected unit and if empty, check the alignment of the toner sensor actuator arm. It is possible that the arms may have been jarred out of alignment during shipment and fail to sense the low/empty toner condition. This in turn, causes the IU to drop below the proper toner-to-developer ratio resulting in C-0F3x codes. Once the actuator has been properly positioned, run ATDC toner supply until the T/D ratio comes back into the specified range.
hope that help


or try to reset the machine.........

Minolta CF2001... | Answered on Nov 30, 2011


Every imaging unit has a life. There is a chip which gets signal from imaging unit about when to stop printing. That is the reason when it stops the page before that prints just fine. And we thing that it can print lot more pages. But this is not true. You should buy a new one.

Having said that still there is a way to rest the ram on the chip so that it ignores the signal from imaging unit. You can try to reset that and see if it prints more pages. Here is the instructions to reset.

1 Turn the printer off.
2 Press and hold the GO button.
3 Turn the printer on and continue to hold the GO button.
4 After the Go, Ready, and Attention LEDs turn on, continue holding for at least 20 seconds.
During this process, the Attention, Ready, and Go LEDs will each turn off.
5 Release the GO button.
6 The device LEDs will begin cycling from front to back. The NVRAM-init process runs until the
printer is in the Ready state.
7. Press the red cancel button.

For more info goto here.

Minolta CF2001... | Answered on Aug 16, 2011


reinstall driver again go devices and printers right click printer then trouble shoot it.

Minolta CF2001... | Answered on Feb 15, 2011


This is a common problem i have seen with the scan motor drive belt check the tension on the scan motor is correct and that the drive pulleys are secure on the shaft

Minolta CF2001... | Answered on Feb 01, 2011


C0096 1st Image Transfer Roller pressure/retraction failure

Minolta CF2001... | Answered on Jan 09, 2011

Not finding what you are looking for?
Office Equipment & Supplies Logo

Popular Tags

50 questions posted

Ask a Question

Usually answered in minutes!

Top Minolta Office Equipment & Supplies Experts

Adorjani Laszlo

Level 3 Expert

1316 Answers

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6862 Answers

Ed
Ed

Level 3 Expert

479 Answers

Are you a Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Minolta Office Equipment & Supplies

  • Minolta Office Equipment & Supplies

Most Popular Question

admin password minolta cf2001

  • Office Equipment & Supplies
Loading...