20 Most Recent Pride Mobility Products GoGo Ultra X (3wheel) Questions & Answers


hi Hal, that is a issue around based the brake or connectors to the brake or the micro-switch that is moved when you move the drive , freewheel lever.. ... firstly make sure the scooter is in drive mode and not free-wheel mode ., where the axle comes apart you will see a number of connectors , make sure they are a good fit ...

Update me please...

Regards
Rob

Pride Mobility... | Answered on Oct 29, 2015


If the brake release lever is not working by this I mean the lever will not move the release position, this could be a case of the brake mechanism has seized up due to water or that sand and grit has got in the brake jamming it.

Try a spray of WD40 on the bake lever mechanism and work the lever back and forth. Failing that brake will need to be replaced.

Pride Mobility... | Answered on Oct 24, 2015


hi, okay that a system controller fault however it can also be a loose connection around the controller area, removing the connectors that go into the controller has worked for me, if not it's normally a resistor network inside the controller.

I offer a free testing and repair service ...

Regards
Rob

www.gewizrepairs.co.uk

Pride Mobility... | Answered on Jul 24, 2015


While pulling up on the cover, gently press on the battery box sides to determine if detents are holding the cover on. One a detent is pressed away, the cover should come up.

Ensure no connectors are holding the pieces of the battery box together.

Pride Mobility... | Answered on Mar 16, 2015


5 beeps usually means scooter is out of gear, but since the lever is in the drive position and the scooter gearbox/differential is engaged, it seems that the controller is not sensing the gear change. Possibly a faulty micro switch in the motor housing can be the cause of this, usually the micro switch is pressed down by the drive lever and if the switch is pressed down the motor controller knows the scooter is in gear.

Pride Mobility... | Answered on Feb 12, 2015


Six beeps would say it is the throttle pot not in its centre off position or the pot needs replacing. Is the wig wag lever loose by this I mean the lever is wobbly and moves up and down a fair bit. This would indicate its had its day. Have you had speed issues before this problem as this is normally the case before they go wrong altogether.

Pride Mobility... | Answered on Nov 25, 2014


7 flash code is: Throttle control fault.

1. Check wiring for open/short circuits.
2. Check the throttle set-up.... The ohms should be very close to each other when placed checking forward and reverse on set up.

Pride Mobility... | Answered on Aug 26, 2014


Well If the scooter has been sitting without use since 2011 then you cannot recharge them you'll have to replace them they would be dean at tis point.

Pride Mobility... | Answered on Jul 21, 2014


Make sure it is placed in gear, sounds like it is in the Neutral free wheel position.
If the scooter moves easy when you push it, it's just in free wheel.

Pride Mobility... | Answered on Mar 25, 2014


The wiring interconnects on these scooter are all modular and the blow up assembly diagrams are all you need to trace the wiring and replace components. Aside from a dealer log in to the manufacturer's website you can go to southwest medical's website and get all the information on the wiring and parts. Hope this helps.
SC40X Go Go Ultra Replacement Parts

Pride Mobility... | Answered on Mar 06, 2014


hi, okay if it's the loading effect on the batteries, not a loose connection, then look at the speed pot, when it slows down try pushing the lever upwards or downwards, improves then the pot needs replacing , this is a simple test to see whether the tracks within the pots are worn...

Regards
Rob

www.gewizrepairs.co.uk

Pride Mobility... | Answered on Mar 03, 2014


you could have a bad throttle pot o speed pot possibly a key switch problem aswell. Hi I a Phillip the "DFW Mobility Specialist"send me a email at dfwmobilityspecialist@yahoo.com if you live in or near the Dallas Fort Worth area.

Pride Mobility... | Answered on Apr 11, 2013


9 flash code usually happens when the battery connection is interrupted while the key switch is turned on. On Go Go Ultra series, there is a spring loaded terminal post that the battery box sits on to make the connection. Sometimes as this spring wears out, the connection will be interrupted then reconnect again while driving causing the 9 flash code. try putting a nickel on each of these battery connections underneath the battery box and see if that fixes the problem.

If you do need to take the shroud off, flip on it's side, there are 4 small bolts that bolt the shroud to the frame from the bottom side. they're easily visible. Hope this helps.

Pride Mobility... | Answered on Apr 02, 2013


hi , that could be a faulty reset switch, I come back later and give you a more complete reply as i run out of time now.

Regards
GeWiz

Pride Mobility... | Answered on Feb 16, 2013


sounds to me like you have a bad cell in the battery. i would try a new one. if this is new it may be under warrenty. remember just because somethings new dosent guarentee it works properly. if you get a new battery and the same thing happens it could be a charging problem or short with the chair.. i hope this helps you

Pride Mobility... | Answered on Jun 04, 2011

Not finding what you are looking for?
Pride Mobility Products GoGo Ultra X (3wheel) Logo

32 questions posted

Ask a Question

Usually answered in minutes!

Top Pride Mobility Products Health & Beauty Experts

Rob Hill
Rob Hill

Level 3 Expert

1412 Answers

Will

Level 1 Expert

25 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Pride Mobility Products Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Pride Mobility Products Health & Beauty

  • Pride Mobility Products Health & Beauty

Most Popular Question

go go ultra

  • Health & Beauty
Loading...