20 Most Recent Cisco Linksys E2000 Advanced WirelessN Broadband Router Network Routers Questions & Answers


You can Find the Downloads Here

http://homesupport.cisco.com/en-us/wireless/linksys/E2000

Cisco Linksys... | Answered on Sep 19, 2019


that would be logical considering that there are 2 different countries with completely different network systems

Cisco Linksys... | Answered on Feb 01, 2018


Since you flashed your router, you need to reset your modem as well, so it recognizes the "New" router. Turn off both router and modem. Turn on modem first, give it a minute to boot up, then turn on router and you should be ok.

Cisco Linksys... | Answered on Nov 20, 2017


Hi,

You can block the access through Access restriction module. Please refer Block site on E2000 1 0 04

Cisco Linksys... | Answered on Aug 07, 2014


Firstly log into your router from your computer. If you don't know the username and password, try the default one which is Username: admin Password: Admin. Check under Wireless setting and you will see the current password listed there. You can change it to a new one if required. Just remember to save after you've done any changes.

Cisco Linksys... | Answered on Aug 06, 2014


Are you able to browse any other web pages through your router? If you are not able to view the speed test page alone, Then it might be a flash problem. Most of the speed testing pages uses flash and you might require a latest flash player to be installed on your system.
You can better visit ScanmySpeed.Com to test your internet speed. This website doesn't require flash to test internet speed.

Cisco Linksys... | Answered on May 03, 2014


either admin/admin or admin/password are the defaults.

Cisco Linksys... | Answered on Dec 30, 2013


1.login to your linksys.
2.go to access and restrictions.
3.click the drop down for access policies and for each selection,check facebook has been added to the url section.
4.if found, you can either delete facebook from that policy of disable the whole policy.

Cisco Linksys... | Answered on Nov 08, 2013


Disconnect the power from the linksys for about 30 seconds then plug it back and see if it stops dropping. Most times the dropping occurs if you turn the modem and router off at night then when you turn them back on the router boots up faster than the modem and that will cause it to drop. Power outages also will cause the problem if the router boots up before the modem.

If unplugging the router and waiting 30 seconds does not solve it then unplug both the modem and the router. Then plug the modem back in and let it boot up for a minute or two, then plug the router in and let it boot up.

Cisco Linksys... | Answered on Jun 13, 2013


To connect to your wireless router, the router's wireless settings needs to be configured with the SSID, encryption etc. and also the wireless cards in all the laptops/computers needs to be configured with these router's wireless settings. Then the laptops/desktop computers can communicate with your wireless router.
Connect a LAN cable from the Linksys to the LAN port on your computer.
Open a browser and enter the Linksys configuration URL
https://192.168.1.1
The default login = admin
The default PW = admin
You can protect your router by changing the default admin PW (write it down and put it in a safe place)
Go to the wireless configuration and set up the SSID and WPA or WPA2 encryption.
Now apply these settings to the wireless card in your laptop/computer.
To secure your wireless network from unauthorized access, please click on this link and follow my instructions :- https://www.fixya.com/support/r3559128-wireless_router_security

Cisco Linksys... | Answered on Oct 16, 2012


Error 800: Unable to establish VPN connection

This issue may be caused by a router that has outdated firmware.

Make sure that port 1723 is opened on your router.
For VPN connection , you can try opening port 500, 443-447, 10000-20000 and important port 1723 on your router.

I will suggest you to upgrade firmware on your Linksys router.
After upgrading the firmware, reset the router to factory default and reconfigure it manually.
Open the ports mentioned above and see if that works.

See How to upgrade firmware on Linksys router.

See How to setup Linksys router

Cisco Linksys... | Answered on Mar 13, 2012


open your browser to 192.168.1.1
default login/pass is admin
go to wirelessgo to wireless security and apply a password to your guest network.

Cisco Linksys... | Answered on Mar 11, 2012


Who is your Internet service provider?

If it is a DSL company then in some cases the router IP address may change to 192.168.0.1.
What happens when you try to open 192.168.1.1.
Does it ask you for user name and password?
Did you install router using cisco connect software?
Open cisco connect software.
go to router settings.
Click on Advanced settings.
It will open the setup page.

See Linksys E2000 router setup

Cisco Linksys... | Answered on Mar 07, 2012


Please check whether your computer's wireless connection enabled or disabled. If you are using windows 7 this information you can find in network sharing center. By accident if WLAN is disabled it can be enabled. Also power cycling the router may do the trick.
More drastic approach is resetting the router which I recommend to reserve as last resort. With information you provided the router seems to be fine and your computer wireless need to be enabled!
good luck!

Cisco Linksys... | Answered on Sep 12, 2011


Normally userame and password of linksys Router is admin and admin respectively, if it is not changed,
if still can't access, you can reset your router by pressing and holding reset button for few seconds,
Thank you, Please don't forget to rate me.... please

Cisco Linksys... | Answered on Aug 28, 2011


yes you can change it. Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter... Leave Username blank & in Password use admin in lower case... Click on the Wireless tab>Click on Advanced Wireless Settings... Change the wireless channel Also,Under the Advance Wireless Settings on the router,Change the N Transmission Rate to 15-130Mbps and click on save settings

Cisco Linksys... | Answered on Jul 26, 2011


Make sure the power cable jack in the router is not clogged with anything and that the actual cable hasn't been worn down and still fits. Besides that, you could try unplugging your computer, and plugging the router into that outlet to see if it's not a bad power outlet. If it still doesn't work it might just be time for a new router.

Cisco Linksys... | Answered on Jul 22, 2011

Not finding what you are looking for?
Cisco Linksys E2000 Advanced WirelessN Broadband Router Network Routers Logo

83 questions posted

Ask a Question

Usually answered in minutes!

Top Cisco Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Jeffrey Groves
Jeffrey Groves

Level 3 Expert

573 Answers

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Cisco Computers & Internet

  • Cisco Computers & Internet

Most Popular Question

bought router set up netflix thru wii

  • Computers & Internet
Loading...