20 Most Recent Cisco Linksys E1000 WirelessN Broadband Router Network Routers - Page 9 Questions & Answers


There are differences between them. One is for access to yuor PC and one for your router configuration and management.

Cisco Linksys... | Answered on Oct 24, 2010


You will need to check the wireless settings of the router.
If your network is secured then make sure that you are typing the correct network key.
also make sure that the DHCP server is enabled on the router.
is there any computer connected to the router ?
If yes then you can open the router set up page on that computer.
Router set up page is the page where you can check all the wireless settings of the router.
Click here for step by step instructions

Cisco Linksys... | Answered on Oct 18, 2010


E1000 router is not a dual band router.
It works only on 2.4 GHZ wireless signal.
You can try changine the wireless channel on the router.
If you have installed the Cisco conect software on your computer, then open the Cisco connect software. Go to router settings. Click on advanced settings. It will open the setup page of the router. Go to wireless tab.
Set the configuration view to Manual.
change the channel to 11. See if that works.
If not then change the channel to 1 and check it.

Click Here for more information about the routers and network

Cisco Linksys... | Answered on Oct 15, 2010


Press the reset button on the router and hold it down for 30 second. Wait for 10 seconds. Now unplug the power to the router and plug it back in. Wait for 1 minute.
The router will be back to the factory default settings. Now run the CD that comes with the router. Install the Cisco connect software and see if that works.
If the Cisco connect software is not working then you can try to etup the router manually without the CD.
Click here for more informartion about router setup

Cisco Linksys... | Answered on Oct 09, 2010


Unfortunatly there is no way of accessing the router security key if you have forgotten it however you can reset your router to factory default here is how
" The Reset button is located on the right side of the product label. There are two ways to reset the Router to its factory defaults. Either press and hold the Reset Button for approximately five seconds, or restore the defaults from the Administration > Factory Defaults screen in the Router's browser-based utility The Reset button is located on the rightside of the product label. There are two ways toreset the Router to its factory defaults. Either pressand hold the Reset Button for approximately five seconds, or restore the defaults from the Administration > Factory Defaults screen inthe Router's browser-based utility" was this helpful?

Cisco Linksys... | Answered on Oct 05, 2010


If you have forgotten the security key for the router the only thing you can do is reset it however by resetting the router will reset the router to default settings keep that in mind here is a link to user manual it should help you with resecuring it http://home.cisco.com/assets/presskit/userguides/e1000_ug.pdf

Cisco Linksys... | Answered on Oct 02, 2010


Check this link
http://fixhomenetwork.com/blog/linksys-e1000-e2000-e2100l-e3000-router-setup/
Set up a Linksys Wireless Router
  • 1 Choose and purchase a Linksys router, taking into account your budget and computing habits.
  • 2 Attach the antennas to the Linksys wireless router.
  • 3 Place the router in a central location, making sure it's not surrounded by metal. (A signal can't be obtained through metal.) The router should be located so that the distance between clients (computers) is somewhat equal. This will create a better connection.
  • 4 Plug the Ethernet cable into the "Internet" port on the back of the Linksys router.
  • 5 Connect a computer to the router by plugging another Ethernet cable into the Ethernet port on your computer and attaching the other end to one of the available ports on the back of the router. You can choose any port except the one labeled "WAN."
  • 6 Plug the router into an electrical outlet.
  • 7 Wait for the power light to stop flashing, at which time the router is finished booting up. While the router is booting, the power light will be blinking. This process may take a few minutes to complete.
  • 8 Reboot your computer so it can access a new IP address from the router through the Dynamic Host Configuration Protocol (DHCP).
  • Configure the Router
  • 1 Open your web browser, type " http://192.168.1.1/ " into the address bar and hit "Enter."
  • 2 Use "Admin" as the username in the pop-up box and leave the password blank.
  • 3 Connect to the Internet and click on "Internet Setup."
  • 4 Select your connection type from the drop-down menu. Choose "DHCP" for cable modems or "PPPoE" for most DSL modems. If you are unsure of these options, check with your ISP.
  • 5 Set a service set identifier (SSID) to identify the router and change the password.
  • 6 Encrypt your wireless connection using a Wireless Encryption Protocol (WEP) key. Under the "Wireless Security" option, enter a passphrase and click "Generate." This will generate a password which will need to be used by any client connecting to your router.

  • Cisco Linksys... | Answered on Sep 27, 2010


    If you didn't change it by default it is:
    username: - leave blank - password: admin
    Everything related to your router is HERE.
    Hope this info helps ;)

    Cisco Linksys... | Answered on Sep 26, 2010


    ycrainville

    Question are you getting this message when you install the setup CD for the router. I have not see the new Linksys CD but it sounds like it may be scanning your system to see if you have a wireless card in it. If you do not then you can ignore the message.

    If you do that I can help you get your computer connected after the fact. Note the only need for the CD setup is really to configure the connection between you modem and the router. All the other setting can be setup in the routers interface.

    Let me know if you still have trouble getting on the internet atleast while you have the computer hard wired and we will look at your setting and connections.

    After you get Internet I can help you get your wireless working. Also note when setting up a wireless router you need to do the setup while it is wires because you can change a setting that will kick you off and if you can not reconnect wirelessly you may need to reset the router and start over if you were not hard wired.

    Issken
    http://www.fixya.com/users/issken

    Cisco Linksys... | Answered on Sep 04, 2010


    If you connect the computer to the router , it works.
    That means the wired connection is OK.
    Open the set up page of the router check the wireless settings of the router.
    I think your network is secured and you are not typing the correct network key.
    just open the router set up and check the wireless settings .
    Make sure that the DHCP server on the router is enabled
    Click Here for step by step solution

    Cisco Linksys... | Answered on Aug 15, 2010


    usually the passkey will be found in the bottom of router, named as wep key...

    you can log in to the router interface by typing the ip address of your router in any web browser, and you can find what is the password...

    the ip address of linksys router will be 192.168.1.1

    it will never change unless u changed the ip address of your router manually...

    Cisco Linksys... | Answered on Aug 12, 2010


    hi

    you traing at time 2 modems chack IP of Motrola and linksys if you want to using linksys then just configure you local setting on linksys
    it has a both 2gethe modem and router

    try linksys alone with your DSL line

    Cisco Linksys... | Answered on Jul 16, 2010


    check the wireless settings of the router. The wireless security might be set to WPA2/WPA mixed. Open the cisco connect software and check the wireless settings. If you are not able to change the settings using the Cisco connect software then you change the settings manually by opening the set up page of the router.

    Click Here for step by step instructions

    Cisco Linksys... | Answered on Jul 16, 2010


    Your wireless network must be secured
    You will need to check the wireless settings of the router.
    Is there any computer online using the router.
    check the IP address on that computer.
    If yes then you can open the router set up page on that computer.
    router set up page is the page where you can check all the router settings.
    Click Here for more information about the routers and network

    Cisco Linksys... | Answered on Jun 24, 2010


    You are getting the pop up asking for Internet access server drivers.
    actually that is a bug in the Cisco connect server.
    You can uninstall the cisco connect from that computer and reinstall the CD.
    OR go to the device manager on that computer.
    Under other devices you will find that internet access server with the yellow exclaimation mark.
    Right click on it and disable it.
    You can also setup E1000 router without CD or Cisco connect software.
    Click here for more information

    Cisco Linksys... | Answered on Jun 11, 2010


    DO NOT CALL FAKE NUMBERS OR GO TO FAKE WEBSITES. These phony support numbers send you to criminal call centers where they will install malware, steal ID and/or extort money from you. Please only ever use the support contacts from the official company website.

    Cisco Computers... | Answered on Oct 21, 2019

    Not finding what you are looking for?
    Cisco Linksys E1000 WirelessN Broadband Router Network Routers Logo

    226 questions posted

    Ask a Question

    Usually answered in minutes!

    Top Cisco Computers & Internet Experts

    Prashant M
    Prashant M

    Level 3 Expert

    2277 Answers

    Ekse

    Level 3 Expert

    13434 Answers

    Jeffrey Groves
    Jeffrey Groves

    Level 3 Expert

    573 Answers

    Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    View Most Popular

    Cisco Computers & Internet

    • Cisco Computers & Internet

    Most Popular Question

    signs wireless router failure death

    • Computers & Internet
    Loading...