20 Most Recent OKI B8300 Laser Printer Questions & Answers


Try to update printer driver to your system and use cable first time to install and configure.

Error Code 0xE0000007 for Microsoft Office Outlook and Windows Updates

OKI B8300 Laser... | Answered on Jun 06, 2018


Has the cartridge got a chip? Does this chip need replacing?

OKI B8300 Laser... | Answered on Feb 11, 2015


I have an error code L4-02 with Oki B8300. what is the solution?

OKI B8300 Laser... | Answered on Apr 25, 2014


Hi,

H5-01 means that the paper sensor in the fusing unit is defective and needs to be replaced. If you open the machine and clean the entire area around the fuser unit sometimes that will clear the error as well.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

OKI B8300 Laser... | Answered on Mar 07, 2011


HI there ERROR H5:01 mean mechanical problem. This error code says call service person for copier.

OKI B8300 Laser... | Answered on Jan 25, 2011


http://www.printcopy.info/shop_e/cdrom.php?brand=OKI

Here is a link to service manuals for OKI

OKI B8300 Laser... | Answered on Feb 17, 2008


H4-01 Heat roller low temp is correct.

You machine has a fuser unit that it uses to bond the toner to the paper, it does this with  a heater lamp heating a set of rollers that the paper passes threw after it has printed.

Your machine monitors this unit to regelate its temp, your machine is sensing via a thermister and thermal fuse the temp of the fuser unit is not hot enough to enable use, this would mean the heater lamp is blown, thermister is faulty or thermal fuse blown 95% chance it's the lamp,

What one normally does is replace fuser assembly with new this is not a user thing it requires a tec, but if your into it, it is the hi voltage hot bit near paper exit.

OKI B8300 Laser... | Answered on Oct 31, 2007


From Oki's site: Symptom: The toner counter did not clear after installing a new toner cartridge. Cause: The printer was not powered off when the new toner cartridge was installed, Therefore the counter did not cleared. Resolution: 1. Enter the PCU Diagnostic Mode, By turning off the printer and holding down the MENU and OK buttons on power up. (Release the buttons once you're in the PCU DIAG MODE) 2. Press the MENU button 14 times until the operator panel reads " Counter Display " 3. Press the MENU button and the BACK/C button at the same time, This will put the printer into the Feed Counter Clear Mode (Release the buttons once you're in the Feed Counter Clear Mode) 4. Press the up arrow 5 times until the operator reads " Toner Counter Clear " 5. Press the OK button, The operator panel will now display " Toner no " 6. Press the up arrow once and the operator panel will display " Toner yes". Now press the OK button and the green data light will flash to indicate that the clear process is complete 7. To exit the PCU Diagnostic Mode, By turn the printer off and then back on this will allow you to exit the PCU Diagnostic Mode Hope that helps. If it does not please let me know Ed

OKI B8300 Laser... | Answered on Jun 16, 2007


Ensure that the desired paper is set in a paper tray of the printer and select [Auto] in the paper selection of the printer driver. You may need to configure the margins in the sofware you are using. hope this will help you Daniel

OKI B8300 Laser... | Answered on Feb 02, 2006


That is a paper jam code. Reopen the cover, and clear all paper jams. Close the cover, and then I would reset the machine by turning it off and on if the code continues. http://www.german-parts.de/oki_manual/paperjam/stau_b400_series.pdf

OKI B Office... | Answered on Feb 05, 2015


Open the lid. Mounted under the lid you should see a horizontal bar which is actually the laser [LED]. Once your toner cart has emitted, enough loose toner has accumulated on the laser that it can no longer draw on the page correctly. Using something soft and barely dampened with water [use a soft cotton cloth, NO PAPER PRODUCTS, no dirty rags, etc] and wipe gently from L to R to remove the loose toner. Turn to a clean section of the cloth and do it once more. GENTLY! No pressure, do not scrub it, or you can damage the laser. Close the lid and print something. You should be back to good now.

OKI B Office... | Answered on Nov 26, 2014


1. change cartrige if problem not solved 2. there is mechanic problem 3. or LSU optics are not clear

OKI B Office... | Answered on Aug 27, 2014

Not finding what you are looking for?
OKI B8300 Laser Printer Logo

20 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top OKI Office Equipment & Supplies Experts

WTF Chuck.....
WTF Chuck.....

Level 3 Expert

387 Answers

Clive
Clive

Level 3 Expert

4345 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you an OKI Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

B OKI

  • B OKI

Most Popular Question

h5 01

  • Office Equipment & Supplies
Loading...