Top 20 CreoScitex EverSmart Jazz+ Flatbed Scanner Questions & Answers


click start, control panel ,add or remove programs, remove scanner program. reinstall with cd . after installing search for any up dates and drivers and install , follow instructions in the install manual as to when the scanner is switched on.

CreoScitex... | 118 views | 1 helpful votes


find a new driver and utilities disc

CreoScitex... | 86 views | 1 helpful votes


Hi Ralph
What OSX are you running on your Mac G5 and is this an Intel or Power PC? You will find that the Jazz Scanners are only supported up to G4 OSX10.3.9 and no higher.
You may get lucky and find it may work but you will get numerous crashes for no reason and the scanner will also just freeze and you will have problems with the BGCAR application that the scanner application uses.
Sorry cannot be more helpful.
Creo/Kodak Scanner Engineer

CreoScitex... | 278 views | 1 helpful votes


take a look on the device support site and see if you have driver available for it ...and only after that change the operation system ..if you do not find another driver for a newer OS ..install again the same one ..and use the old drivers ...Reinstalling it will make it run like new ..it is probably just bugged..or if youre intention is to change the MAC with a newer one that will allow you to use a newer OS ..than also see if it will be any driver available first ..otherwise it will be useless with the scanner

CreoScitex... | 145 views | 1 helpful votes


call me i will hook you up with number etc....9175133131

CreoScitex... | 436 views | 0 helpful votes


You should contact genesis equipment in AZ.
http://www.genesis-equipment.com/
I've ordered bulbs from them for my Jazz+. Kodak no longer supprots the Jazz, Jazz+, Pro, and older, so you'll have to find alternative suppliers for parts. Genesis should be able to help and can do the work for you if needed, but crating and shipping something this large wouldn't be cheap. You'd probably better off just buying a replacement at that point.

CreoScitex... | 311 views | 0 helpful votes


Hi!. You need to create tables using the Oxyjen Installion Utlities. Make sure that your Calibration side is positioned properly and the four foucus types are calibrated. Once the tables are created, save them to the appropriate tables folder.

CreoScitex... | 674 views | 0 helpful votes


Yep, i have an installation cd from 342L to JAZZ+, if you are interested i can to upload to my FTP for 50 dollars avklnkva@gmail.com. Greetings!

CreoScitex... | 364 views | 0 helpful votes


i have a lot of lamps scitex for this just i am from mexico: a.suarez@centergraphics.com.mx

CreoScitex... | 912 views | 0 helpful votes


I have the same problem any fixes?

CreoScitex... | 304 views | 2 helpful votes


surely damage the motion board, if you are interested in a board please send me the part number and the model of you scanner for check my stuff and to proof it. I am in México, Greetings!

CreoScitex... | 191 views | 0 helpful votes


UPDATE:


I've now managed to solve this initial problem by installing the relevant extension for the SCSI PCI card, however when I try to launch the scanner software the error message 'No communication with scanner" pops up

I've tried the obvious cables check etc. Any ideas?

Thanks

CreoScitex... | 320 views | 0 helpful votes


There are two locks on the scanner. One on the top right corner of the inner lid that locks the transparency assembly. The other for the bed is located on the side of the right hinge. Just turn them with a flathead screwdriver.

CreoScitex... | 162 views | 0 helpful votes


There's either a problem with the power supply or the control board, most likely the control board. Have you tried running the diagnostics yet?

-Ryan
omnicow at gmail dot com

Creo Office... | 260 views | 0 helpful votes


SDK - Android Software Development Kit. In this toolkit, you can reset your Device finely by using data cable. you have to follow simple steps. Go to this link and Download SDK and type "adb shell" and type other codes to reset.
Alternative softwares - In this option, you are able to do a factory reset your Uoogou M2 by using your laptop or your computer (Recommended)

Office Equipment... | 115 views | 1 helpful votes


Often when removing a paper jam there is a very small piece of paper remaining.
Make sure there is nothing left or it will cause another jam to occur

Office Equipment... | 340 views | 1 helpful votes


on what ???

Office Equipment... | 42 views | 0 helpful votes


fixya did not sell you a wig or any thing else

Office Equipment... | 52 views | 0 helpful votes


whats the question?

Office Equipment... | 30 views | 0 helpful votes

Not finding what you are looking for?
CreoScitex EverSmart Jazz+ Flatbed Scanner Logo

24 questions posted

Ask a Question

Usually answered in minutes!

Top Creo Office Equipment & Supplies Experts

jasbo
jasbo

Level 3 Expert

2239 Answers

Ekse

Level 3 Expert

13434 Answers

Marvin
Marvin

Level 3 Expert

85219 Answers

Are you a Creo Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

CreoScitex Creo

  • CreoScitex Creo

Most Popular Question

always same problem serial number

  • Office Equipment & Supplies
Loading...