20 Most Recent Ademco 6270 Graphic Touchscreen Touch Screen Keypad Questions & Answers


sounds like the system battery may be low. The system batter is usually located , depending on the system, in the main box in a closet. The system battery powers the system in the event of a power outage.

Ademco 6270... | Answered on Jul 03, 2017


A "not ready" message indicates a zone that has faulted. An open door or windows will give this same message. If all the doors and windows are closed, this message will indicate that there is a break or other problem with wiring or an issue has developed with a switch or other sensor hardware.

You should check the hardware for obvious signs of damage, misalignment, etc. Visually check exposed wires to be sure none are pinched, broken, or shorted. *Most* security systems operate at very low voltages (24 volts or less), so danger from burns or shock are minimal if yours is such a low voltage system. Make adjustments, repairs or replace as needed. If uncomfortable making these repairs - or are unsure how to do it - call the installer or other reputable alarm service company or electrical contractor to do it for you.

I hope this helps & good luck!

Ademco 6270... | Answered on Sep 09, 2011


Sound like u have loose Fiber Optic cables connections cables somewhere,if u tap the side of it comes back brightter.Take the unit aparts and tries reconnected all the Fiber Optic cables tightly if it work.Tries it out the unit turn it on/off 5 or 6 the backlight go up good and bright.Take hot glue gun glue all the Fiber Optic cables connections together for good.

Ademco 6270... | Answered on Aug 11, 2011


Best bet would be to try and contact the prior owner and ask for it! Should have left such instructions for you as part of the sale/exchange. Just try asking if it's possible to do so.

Ademco Home... | Answered on Oct 09, 2019


learn the two into the Code Encryptor receiver by pressing and releasing the black button on the receiver. The red light on the receiver should come on. press and release the closed padlock button 3 times, the red light on the receiver should go off

Ademco Home... | Answered on Oct 24, 2018


Within 30 seconds of power up press *and # simultaneously. Display should say 20, if you press *20 1234 then *99 to exit programming. Your system should be disarmed and your install code should now be 1234. You can then use this code to change the master code.

Ademco Home... | Answered on Dec 08, 2017


You will need to add an Alarmnet wireless communicator device and subscribe to Total connect to interact with a smart phone.

Ademco Home... | Answered on Jul 03, 2017


multiple low battery ones in sequence , mean a remote low battery. There is usually only one reporting zone on the remote (panic). That would be why only one zone shows alarm.

Ademco Home... | Answered on Jun 08, 2017


It should (If installed correctly) be hard wired to a fused unswitched outlet fairly local to the control panel, if that is the case remove the fuse and then the wire to the control panel.

If not you may find it is wired directly to your fuse box, a wall socket or even a ceiling rose. an electrician will easily be able to trace it's source.
An indication as to where it is wired can be obtained by switching/pulling each fuse/mcb in turn untill the control panel powers down.

Ademco Home... | Answered on Feb 24, 2017

Not finding what you are looking for?
Ademco 6270 Graphic Touchscreen Touch Screen Keypad Logo

5 questions posted

Ask a Question

Usually answered in minutes!

Top Ademco Home Security Experts

Sean

Level 2 Expert

80 Answers

oooga boooga
oooga boooga

Level 1 Expert

8 Answers

Vincent Migliore
Vincent Migliore

Level 1 Expert

36 Answers

Are you an Ademco Home Security Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ademco Home Security

  • Ademco Home Security

Most Popular Question

6270

  • Home Security
Loading...