Ademco Honeywell Ademco 944TSP-WH 3/4" Recessed Contact with Terminals and 3/8" Magnet (White) - Answered Questions & Fixed issues


It has been my experience that open ckt on keypad usually means that there is a problem with the wires or the connection to the keypad or control panel. if that is ok then it's the keypad or the control panel. good luck.

Ademco Honeywell... | Answered on Apr 22, 2016 | 76 views


it's a dry contact there is no positive and negitive, it doesn't matter which wire goes which terminal

Ademco Honeywell... | Answered on Jan 06, 2014 | 52 views


Best bet would be to try and contact the prior owner and ask for it! Should have left such instructions for you as part of the sale/exchange. Just try asking if it's possible to do so.

Ademco Home... | Answered on Oct 09, 2019 | 69 views


learn the two into the Code Encryptor receiver by pressing and releasing the black button on the receiver. The red light on the receiver should come on. press and release the closed padlock button 3 times, the red light on the receiver should go off

Ademco Home... | Answered on Oct 24, 2018 | 124 views


Within 30 seconds of power up press *and # simultaneously. Display should say 20, if you press *20 1234 then *99 to exit programming. Your system should be disarmed and your install code should now be 1234. You can then use this code to change the master code.

Ademco Home... | Answered on Dec 08, 2017 | 273 views


You will need to add an Alarmnet wireless communicator device and subscribe to Total connect to interact with a smart phone.

Ademco Home... | Answered on Jul 03, 2017 | 385 views


multiple low battery ones in sequence , mean a remote low battery. There is usually only one reporting zone on the remote (panic). That would be why only one zone shows alarm.

Ademco Home... | Answered on Jun 08, 2017 | 398 views


It should (If installed correctly) be hard wired to a fused unswitched outlet fairly local to the control panel, if that is the case remove the fuse and then the wire to the control panel.

If not you may find it is wired directly to your fuse box, a wall socket or even a ceiling rose. an electrician will easily be able to trace it's source.
An indication as to where it is wired can be obtained by switching/pulling each fuse/mcb in turn untill the control panel powers down.

Ademco Home... | Answered on Feb 24, 2017 | 286 views


Hi, well i suspect that when the power went either out, or more likely when service was restored, the device suffered a "Power Spike, Surge, or Transient" This is an all to common thing, most people do not know how imperative it is to UNPLUG ALL electronic equipment, after the power outage, and only connect a little time AFTER re-connection to avoid any "Nasties" that will occur at the time of and soon after power is reconnected to the grid. Sensitive electronics can and will be damaged by these events as has been evidenced here.
Most likely the power supply unit is damaged, however it may indeed have gone "Deeper' into the electronics without examination one simply cannot tell.
In, my experience, over the many years, these instances i cannot recommend repair, as most often, the very damage done is of a nature that precludes repair, and demands replacement only.
A surge or spike buster device may, assist and are a worthwhile addition, and should always be used regardless on electronics connected to the Mains, however ALWAYS remove totally the connection, in future instances of power outages, to stop this from occurring again.

Ademco Home... | Answered on Feb 20, 2012 | 203 views


The key for the panel is supplied from the distributor and you need to be a certified installer to open an account and buy one, A good old big flat screw driver will open the pannel as well but the lock will be useless after that LOL! (you could screw the dore shut with #6 sheet metal screws after) than you can go on the Ademco's web site to serch for the default code of your alarm panel model but if the installer changed it than you have to reset the panel to factory default and re-program it... (unless the installer activated the installers lock up) than you need the code from the last installer that serviced the panel... if not than you need to send the board to Ademco to have it unlocked or change the board for a new one... (you will still have to re-program everything from scratch...

That's what security is all about!!! $$$$

THE BEST WOULD BE CONTACTING THE LAST INSTALLER FOR SERVICE...

Ademco Home... | Answered on Aug 06, 2011 | 1,130 views


The resolution depends on the code being shown on the keypad. The first two things that come to mind are 1> The control panel's backup battery is low and not accepting a change and needs replaced, or 2> If the code on the keypad shows 'BF', this is Backup Failure, and it means that your backup communications device, such as a GSM Long Range Radio, is not functioning. If you see this code on the keypad, immediately call your local alarm company for a fix. If your communications are down, police / fire / ems will not be dispatched in the event of an alarm.

Ademco Home... | Answered on Mar 06, 2011 | 725 views


Best AI Security Camera with Live Gaurd

Our Surveillance Team has eyes on criminals from the second they step on your front yard. Using multilayers of deterrence: 2-way speakers, strobing lights and the loudest siren, our surveillance agents take proactive steps to deter home burglaries and package thefts. Know More about AI Security Camera and Buy Now
Click Here : https://www.mb103.com/lnk.asp?o=15652&c=918277&a=435048&k=117EF10000D206F5B642A367F43A0D3F&l=16607
deepsentinel-undefined-undefined-0.gif

Home Security | Answered 2 days ago | 2,037 views


Press and hold the Enter button for 15 to 30 second until the DVR restart, After the restart, you DVR default wizard will come up the same way.

Home Security | Answered on Dec 10, 2019 | 791 views


Wooden flooring is known for its elegant look. It creates a warm ambience inside your home. Hardwood floors are elements of d?cor themselves, which are available in many different types and colours. Its durability will ensure a good interior investment while providing aesthetics to your home.

Home Security | Answered on Dec 09, 2019 | 19 views


How do I reset password on my DVR Elec For got password

Home Security | Answered on Nov 26, 2019 | 651 views


The RED "H" is an error with the hard drive on your recorder. There is no easy fix. You will have to refer to a technician/ repairman.

Home Security | Answered on Nov 22, 2019 | 25 views


How do I reset my night owl DVR to factory without remote

Home Security | Answered on Oct 31, 2019 | 3,829 views


Open the unit and trace the power cord connection from the wall plg wire to the FIRST connected control inside the unit. Voila!

Home Security | Answered on Oct 09, 2019 | 80 views

Not finding what you are looking for?
Ademco Honeywell Ademco 944TSP-WH 3/4" Recessed Contact with Terminals and 3/8" Magnet (White) Logo

2 questions posted

Ask a Question

Usually answered in minutes!

Top Ademco Home Security Experts

Brad Brown

Level 3 Expert

18127 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

Are you an Ademco Home Security Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...