Top 20 JVC RX-1028V Receiver - Page 8 Questions & Answers


On the back of the JVC receiver, there should be a TV input, Coax IN and OUT or AUX input (I don't remember if this model had HDMI). On the back of your TV, there should be an AUDIO OUT, connect this to either the TV or AUX inputs and make sure on your TV, to set the Audio Out is On in the TV menu. Turn on JVC and set input to TV and adjust volume. Another way is using the COAX input and outputs. Connect Output of cable box to Input of JVC, then connect Output of TV to Input on TV.

JVC Audio... | 131 views | 1 helpful votes


'protect' means 'shortcut'. Check out speakers, perhaps problems with wires.

JVC Audio... | 145 views | 0 helpful votes


go to JAYCAR or other electronic retailer as they have a range of knobs for audio gear

JVC Audio... | 50 views | 0 helpful votes


go to an electrical retailer or JAYCAR and get one

JVC Audio... | 51 views | 0 helpful votes


There may be an open fuse or power supply failure

JVC Audio... | 97 views | 0 helpful votes


Hi Jeff...
The platter on the JVC LA-10 does not come off as most turntable platters do. It is attached to the spindle with a Philips head screw.

Here are the steps:
Remove dust cover from turntable. Unscrew hinges and lift.
00.jpg" alt="Remove dustcover at hinges.">Remove dustcover at hinges.
  • Secure tonearm to prevent stylus damage.
    00.jpg" alt="Secure the tonearm.">Secure the tonearm.
  • Remove slipmat from platter.
    00.jpg" alt="Remove slipmat.">Remove slipmat.
  • Turn the turntable on its side and remove screws that hold the top to its base. Remove platter by unscrewing the bottom plate from the turntable. The spindle bearing is held in place with a Philips head screw. Loosen it and the platter will separate easily from the spindle.
    00.jpg" alt="Separate the spindle from the platter by loosening with a Philips head screwdriver.">Separate the spindle from the platter by loosening with a Philips head screwdriver.
  • Loop replacement band around the pulley cylinder in the motor. Replace platter and bottom plate. Tighten spindle screw. Test the new belt by turning the platter clockwise two or three rotations. Belt should fit snugly and turn with little resistance.
    00.jpg" alt="Test the replacement belt by turning the platter clockwise.">Test the replacement belt by turning the platter clockwise.




  • JVC Audio... | 713 views | 1 helpful votes


    There will be yes! But if it is as simple as replacing it, I would doubt.

    There's a service manual for the model on e-bay at the moment!
    If you get stuck.
    http://www.ebay.co.uk/itm/JVC-QL-F320-QL-F320B-turntable-service-manual-original-/131584946151

    JVC Audio... | 190 views | 0 helpful votes


    bes!t buy gg greg Walmart or the jvc web site,call them

    JVC Audio... | 60 views | 1 helpful votes


    Repair might be quiet simple or very difficult as it will depend on how much damage has been done. For example it could just be small crack on some circuit board that is the problem, easily repaired. One way to test it would to give it a gentle shake. If you can hear things rattling about inside then expect a big bill!
    If you choose the replacement option then just enter the model number in the Amazon website. If it's still available it will come up, or something else will catch your eye.

    JVC Audio... | 166 views | 0 helpful votes


    Fuses blow when there is an overload. The most likely cause being a short-circuited device in the power amp section.

    JVC Audio... | 73 views | 0 helpful votes


    What exactly is the issue? What part needs to be repaired? It seems to have been discontinued my the manufacturer so parts may be hard to come by or you can try calling the manufacturer and see if they still carry the parts for it and if they can repair it or maybe just mail you the parts. Since its discontinued they won't expect to get to many in and those parts will eventually just be thrown away. I would say just upgrade but after looking at it anything over $250 is for sure worth repairing in my opinion.

    JVC Audio... | 141 views | 0 helpful votes


    If it is the 80 pin job - IC701
    Then this is the number UPD78044GF-067
    Or a few others...
    IC603 - MN35510
    IC601 - AN8806SB

    Any others quote the PCB number and I will tell you it, as I have a copy of the service manual.

    JVC Audio... | 155 views | 0 helpful votes


    Hi looking at female 8 pin din with the groove at bottom this is No 8 going clockwise to the left is pin 6 next is No 1 then 4 - 2 - 5 - 3 - 7. ..Hope this helps..

    JVC Audio... | 290 views | 0 helpful votes


    The following is a link to the manual

    Try relocating to a different location and wall socket. On page 22 one error is the microprocessors is susseptable to electrical interference. (operations are disabled)

    Hope this helps?

    http://resources.jvc.com/Resources/00/00/90/LVT1539-001A.pdf

    JVC Audio... | 51 views | 0 helpful votes


    Start with the simple things.
    • Check left right balance
    • Swap output speakers left to right
    • Swap the speakers at the receiver to make sure no wire open/short
    • Swap input RCA cables left to right red/white - white/red
    Ok No JOY!
    JVC has thermal overload circuits/overload on most of there Amps.

    Remove power for a minute or two to see if there is a reset.

    Rewire speaker connections to speaker set 2.

    Connect REC out to Rec In swap cables and see if problem is in pre-amp or power amp.

    Check internal fuses.

    JVC Audio... | 321 views | 0 helpful votes


    There was an original on e-bay for 19.95. But it appears to out of stock everywhere else.

    As with any Universal model, even if you can find the code that works the unit, it's likely some functions will not work.

    JVC Audio... | 116 views | 0 helpful votes


    See if you can find the factory reset setting. That should restore the settings to normal. Though remotes made for other JVC devices might work some of the controls, they can cause complications.

    American E-Bay does seem to be selling the original remote at the moment. It might be second hand, but at least you know it will work.

    JVC Audio... | 66 views | 1 helpful votes


    http://support.jvc.com/consumer/support/index.jsp

    Under download click on user manual

    If you need further help, I’m available over the phone at https://www.6ya.com/expert/gregg_27a4d257e54e7920

    JVC Audio... | 68 views | 0 helpful votes

    Not finding what you are looking for?
    JVC RX-1028V Receiver Logo

    14 questions posted

    Ask a Question

    Usually answered in minutes!

    Popular Products

    Top JVC Audio Players & Recorders Experts

     Grubhead
    Grubhead

    Level 3 Expert

    5699 Answers

    The Knight
    The Knight

    Level 3 Expert

    76204 Answers

    stynger007

    Level 1 Expert

    33 Answers

    Are you a JVC Audio Player and Recorder Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    View Most Popular

    JVC Audio Players & Recorders

    • JVC Audio Players & Recorders

    Most Popular Question

    stopped working

    • Audio Players & Recorders
    Loading...