JVC RX-1028V Receiver - Answered Questions & Fixed issues


As it is a receiver then it's probably something to do with the amp section. Either the pre-amp or the power amp. If you get no response at all by connecting a tape or cd player to it, then it's likely the pre-amp might have failed.

JVC RX-1028V... | Answered on May 19, 2017 | 6,953 views


hello because theres a dead short somewhere what i mean by this is 1 of the components is faulty this is where you will need to do some checks or take it to an engineer

regards
shaun

JVC RX-1028V... | Answered on May 22, 2010 | 277 views


Unless the TV has an output for Dolby Digital, you can only listen in stereo or a pro-logic modes, or other none digital mode. If you only connect 3 of the 5 speakers, then the other two channels will simply not be heard, but it shouldn't damage the amp.

JVC RX-1028V... | Answered on Mar 01, 2010 | 79 views


hooked up ps3 to amp works great! trying to hook up 2nd blueray player, with 2nd fiber chord. i have it pluged in to dvd port on amp , can"t get no sound ! wat to do ?

JVC RX-1028V... | Answered on Apr 04, 2009 | 496 views


I had a similar problem with a jvc 8040. when I replaced the fuse it became very obvious that the b1560 output on the center channel was blown (smoke and sparks, always a dead giveaway). I haven't fixed the center channel yet but simply unplugged the center channel board and removed it from the unit. Now everything works fine except of course the center channel. Pre outs still operate just fine so a slave amp could be used for center channel power, or you could just go and buy a marantz amp; I did and then I realized that I was lucky that the old jvc quit.

JVC RX-1028V... | Answered on Mar 04, 2008 | 516 views


First thing to do is to take out the batteries out of the remote and see if it still turns on by itself. If it doesnt, go to http://www.remotes.com and get a new one. If it does still have a problem, Its most likly in the remote IR sensor or the microprocessor and this has or should be diagnoised by a trained tech as its all solid state and the way to do this would be to look at the waveforms in the remote,microprocessor,and power supply circuit. Good Luck

JVC RX-1028V... | Answered on Dec 15, 2007 | 105 views


Unplug the unit from AC power for 30 minutes, and disconnect all of the speakers and other associated equipment. Upon plugging back in, press and hold the power button at the same time for 5-10 seconds to force a hard reset.

JVC Audio... | Answered 3 days ago | 12 views


Hi hope this helps. ....cheers
img_20191125_205449-gpamlzw2j01svqruoryfocaa-3-0.jpg

JVC Audio... | Answered on Nov 26, 2019 | 53 views


Hi Honwani, indicates model of the JVC team you are commenting on, in order to find the best possible solution
I wait your answer
Regards Franco Dosil

Hola Honwani, indica modelo del equipo JVC del que estas comentando, para poder encontrar la mejor soluci?n posible
Espero tu respuesta
Saludos Franco Dosil

JVC Audio... | Answered on Aug 26, 2019 | 41 views


Hi Leonard Oliver, what are you needing a JVC tape player ?, indicates the model
I wait your answer
Regards Franco Dosil

Hola Leonard Oliver, que estas necesitando de un reproductor de cintas JVC?, indica el modelo
Espero tu respuesta
Saludos Franco Dosil

JVC Audio... | Answered on Aug 15, 2019 | 30 views


Hello Paul, what you have found is a cassette recorder rewriter of two mechanisms, commonly called "Double Cassette"
to be able to listen or record, you would have to connect it to an amplifier that has a Tape input
You can not connect directly to the speakers, unless the speakers have their own amplifier, if so, you would need a cable from two RCA to two RCA
I hope you serve my comment
Greetings Franco Dosil

Hola Paul, lo que has encontrado es un reproductor grabador de cassette de dos mecanismos, com?nmente llamado "Doble Cassettera"
para poder escuchar o grabar, tendr?as que conectarlo a un amplificador que tenga entrada de Tape
No puedes conectarle directamente a los parlante, salvo que los parlantes, tengan amplificador propio, si fuera as?, necesitar?as un cable de dos RCA a dos RCA
Espero te sirva mi comentario
Saludos Franco Dosil

JVC Audio... | Answered on Jul 26, 2019 | 47 views


Go to the speaker selector and set it tonone or headphones...

Good luck!

JVC Audio... | Answered on Jun 10, 2019 | 48 views


depends on model some dont have a jack

JVC Audio... | Answered on Jun 01, 2019 | 60 views


Hello Velile, indicate the model of your Home Theater JVC, to find the best possible solution
Try disconnecting your JVC from the socket, then check that the cables that go to the speakers are well, that they are not peeled or shorted, after checking, reconnect and see if you are still in Protect
If you continue in Protect, I suggest you contact a specialized technical service
I hope you can solve the problem
Greetings Franco Dosil

Hola Velile, indica el modelo de tu Home Theater JVC, para poder encontrar la mejor soluci?n posible
Prueba desconectar tu JVC del toma de corriente, luego revisa que los cables que van hacia los parlantes se encuentren bien, que no se encuentren pelados o en cortocircuito, despu?s de revisar, vuelve a conectar y f?jate si sigue en Protect
Si continua en Protect, te sugiero te contactes con un servicio t?cnico especializado
Espero Puedas resolver el problema
Saludos Franco Dosil

JVC Audio... | Answered on May 21, 2019 | 32 views


Hi Mark, so you account for your JVC, you are not reading the CD, should you indicate on the display, "NO DISC", have you tried to clean the lens of the laser reader, with a cotton swab with a little alcohol?
Another possibility would be that you had, low emission of the reader, which could be adjusted, using the necessary instruments
If after cleaning the reader, it does not work, I suggest you look for a specialized technical service
I hope to solve the problem
Greetings Franco Dosil

Hola Mark, por lo que cuentas tu JVC, no esta leyendo el CD, deber?a indicarte en el display, "NO DISC", has probado limpiar la lente del lector l?ser, con un hisopo de algod?n con un poquito de alcohol?
Otra posibilidad seria que tuvieras, baja emisi?n del lector, el cual se podr?a ajustar, utilizando el instrumental necesario
Si despu?s de limpiar el lector, no funciono, te sugiero que busques un servicio t?cnico especializado
Espero logres resolver el problema
Saludos Franco Dosil
https://elektrotanya.com/jvc_fs-d88.pdf/download.html
https://www.manualslib.com/products/Jvc-Ux-D88-4185098.html

JVC Audio... | Answered on May 15, 2019 | 68 views


Unplug the unit for a minute or two then plug it in and try opening again. If that doesn't work try taping on the door while pressing the 'open' button.

JVC Audio... | Answered on Apr 28, 2019 | 181 views

Not finding what you are looking for?
JVC RX-1028V Receiver Logo

14 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top JVC Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5699 Answers

The Knight
The Knight

Level 3 Expert

76237 Answers

stynger007

Level 1 Expert

33 Answers

Are you a JVC Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...