20 Most Recent Toshiba 61H71 61" Rear Projection Television Questions & Answers


There are several different sheets of plastic that cover your screen. The outside one is the screen protector, the middle one is the lenticular screen, and the inside one is the fresnel screen. All are available at Encompass.com

Toshiba 61H71... | Answered on Nov 25, 2016


Hello, the i.c.'s are a STK-392-110E, there are also small Pico fuses that open up when the i.c.'s short. if you look on-line there are kits you can buy to replace the defective parts. oh and by the way your set is a projection set not an lcd type.tks

Toshiba 61H71... | Answered on Nov 08, 2013


is it yellow as it blinks or red? if yellow check the kill switch located at the base of the lamp compartment cover ensure it presses the switch lever in order to ser the tv to standby mode the yellow blinking will stop and u will see a stable red ready for switching on

Toshiba 61H71... | Answered on Jul 19, 2013


hi
yes there about 5 other more but they are very
small and light green ranging from 2 to 4 amps
on power deflection board

Toshiba 61H71... | Answered on Oct 02, 2010


When was this tv has it projection lamp last replaced?If 1 1/2 or 2 years.Tv on an used like 4 or 5 hours a day.The projection lamp life is over.Require change another projection lamp.U hear alot of clickings too?That mean the board call the Ballast board it also dead,and require changing too.This Ballast board,help to ignite the projection lamp.

Toshiba 61H71... | Answered on Aug 14, 2010

Tip

Why my TV does not start up and remains in standby?


Try first leaving the TV power cord unplugged for some times, let say one hour or so.

Also ensure that the fault is not coming from a faulty receiver box sending bad signal, check if you get same problem on dvd with no receiver box connected.

If that does not work, and you keep having a flashing led on front of the TV, and tv turning off by itself after a while, that indicates a fault condition.

The flashing light indicates a diagnostic state called protection.
When the Monitor goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic chargesaccumulating on capacitors, or because of a wrong voltage read by themain chip on your monitor controller board. this started the protectioncircuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , startingthe flashing light.


If you are in situation one, then theTV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

Common faults that can occurr are a blown capacitor on power board, a convergence IC has blown, or a fault on Digital board.

Check also the video cable or any external connection cable, if the cable is shorting, or the connector is bad, you can get same flashing statebecause of the video cable.

Try moving the video cable, and if the cable is not built in, then also try a replacement cable.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

on Aug 12, 2010 | Toshiba 61H71 61" Rear Projection...


These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. This is called convergence.

When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

Convergence problems are very common on all Projection TV sets including Sony2_bing.gif,Samsung, JVC, Philip Magnavox, Panasonic, Akai, Pioneer2_bing.gif, Hitachi, Zenith, and others. You can get a convergenece repair kit wiith instructions from the links below.

Here are some of the most common problems with these sets...

Problem #1) Convergence

Yours may have one or more of the following symptoms

  • Screen Looks 3-D
  • Colors wont align
  • Screen may look distorted or warped
  • No Audio/Video - makes a chirping sound.
Problem #2

Another common problem is dull or washed out video.

Your set may have one or more of the following symptoms....

  • Dull looking picture
  • White looking picture
  • Halos around objects
  • Red/Orange looking picture

You can see some more examples and find a fix here
bb0cf99.pnghttps://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Toshiba 61H71... | Answered on Apr 14, 2010


so thats why we need 2 hear some sounds but
we noticed that the speakers are sio little 2
hear and the vibrations are so little functionings..

Toshiba 61H71... | Answered on Dec 31, 2009


A Reddish tint means that the Green signal is missing. Does the on screen menu look normal? If so, this points to the signal source. The fact that this happend suddenly, I would check your cables first.
Using YUV?
If the TV's Menu also looks reddish then there is an internal problem with the display.
Good luck

Toshiba 61H71... | Answered on Dec 30, 2009


Ur convergence it dead,Must know how to solders?Buy a convergence kit,replaced what in that kit.Tries Tv Repair World.com,Tvrepairkits.com.

Toshiba 61H71... | Answered on Dec 23, 2009


The parts available list for your 61H shows PD00764 version C as the deflection board for this particular model, it might be that version A would go to a smaller size screen model, toshiba manufactured a 43" and a 53" with this 61" also. So back to your question, all I can say is , if you already have the A version I would compare to version C and keep in mind the connectors(plugs) make sure they are a like, I would imagine that the only diference you would see in the picture would be picture width and vert size. A good idea would be to contact a module rebuilding company(tristate module for example) and get their opinion.

Toshiba 61H71... | Answered on Sep 05, 2009


Resolder jumpers on signal PCB..May be near convergence IC circuit..on 50" model they are 050 & 010. You may have solder cracks..I repaired a 50" toshiba..Let me know if this fixes

Toshiba 61H71... | Answered on May 06, 2009


Ours was doing the same thing, we changed 3 little black fuses in it and it works. I do believe they are 5 amp but not positive, we found them through a tester. When I have the exact answer for u I will email u again sorry u have had no response till now probably does you no good now..It's been awhile since they were changed.

Toshiba 61H71... | Answered on Mar 24, 2009

Not finding what you are looking for?
Toshiba 61H71 61" Rear Projection Television Logo

Popular Tags

38 questions posted

Ask a Question

Usually answered in minutes!

Top Toshiba Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76171 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Are you a Toshiba Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Toshiba Televison & Video

  • Toshiba Televison & Video

Most Popular Question

very little sound comming from speakers

  • Televison & Video
Loading...