20 Most Recent RCA RCU600M Remote Control - Page 4 Questions & Answers

As there are no specific codes for the Dynex TV you have the choice of either using the Auto or Learn method. The following are instructions for both:

AUTO Method

1. Press & Hold (about 3 sec.) the [DEVICE] button on the JUMBO Remote....llight will stay solid.
2. Now just press the [POWER] button (only) ONCE while pointing at the device...it will start sending codes approximately every second. (Don't keep pressing the power button as instructions indicate.)
3. TIMING IS EVERYTHING HERE. (It may take 5 minutes to find your devices code.)
4. AS SOON AS the power goes off...press the [ENTER] button on the JUNBO Remote.
5. Now pressing the [POWER] button should power up/down the device.

---- any buttons not programmed will have to be handled using the LEARN method ---

LEARN Method

1. Press & Hold (about 3 sec.) the [DEVICE] button on the JUMBO Remote....it'll stay solid.
2. Press the [LEARN] button on the JUMBO Remote. (light will immediately blink rapidly.)
3. Now Press the {NEEDED} button to program. (light will stay solid)
4. Now (1 to 2 inches away) have the ORIGINAL Remote pointed at the JUMBO Remote and press the {DESIRED} button on the ORIGINAL Remote.
5. It blinks rapidly while sending...then a slower steady blink once "LEARNED" correctly.

*** Not all buttons work properly with the "LEARN method". Some you will need to "associate" with an alternate button on the JUMBO Remote. *

RCA RCU600M... | Answered on Mar 02, 2010

Try here;


If it's any use, please take a moment to write a testimonial; that way I know how I'm doing!

RCA RCU600M... | Answered on Feb 09, 2010

I noticed the Colby is not in the list of codes. In the case of a code not showing up in the list, I would suggest trying the Auto Code Search. The steps below will help you.

1. Turn on the component (TV, DVD, etc) you want the
remote to operate.

2. Press and hold the CODE SEARCH key
until the indicator light comes on.
Then release the CODE SEARCH key.

3. Press and release the component key that
corresponds to the component you want
the remote to operate (TV, VCR, DVD,
DBS·SAT, CABLE, AUDIO). The indicator
light blinks once and remains lit.

4. Aim the remote at the component and
press the ON•OFF key once. The remote
automatically sends every code for
the specified component one at a time,
with the three-second delay between
each code. Keep the remote aimed at the
component throughout this process.

5. As soon as the component turns off, you
must press the ENTER key immediately
so the remote stores the correct
code. If you do not press the ENTER
key within three seconds, the remote
sends the next code in the list, and you
will have to start over from step 2.

Good Luck,


RCA RCU600M... | Answered on Feb 08, 2010

Hi there,

Well first of all you can try 0091, 0053, 0234, 0155, 0162, 0171 or 0180 If further your remote won't recognized the TV then please post some comment.

Good Luck!!


RCA RCU600M... | Answered on Jan 16, 2010


RCA RCU600M... | Answered on Jan 07, 2010

The codes for a Magnavox VCR are: 021, 060, 062, 104, 106, 115, & 124.

To program your remote by entering a code, follow these steps:

  1. Turn on your VCR.
  2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
  3. Press the VCR button on the remote so that the LED blinks once and then remains solid red.
  4. Enter the first set of 3-digit codes from the list. The LED will blink once every keypress. After the 3rd digit, the red LED will turn off indicating that the code was recognized for the device. If the code was not compatible, the LED will flash several times and you need to return to step 2 to try that code again or to try the next code in the list.
  5. After the LED has turned off, aim the remote at the VCR and press ON/OFF. If the device turns off, you have used the correct code and the remote was successfully programed. If the device does not power off, return to step 2 and try again with the next code in the list.
I hope that helps.

RCA RCU600M... | Answered on Dec 23, 2009

Go here for the manual.

RCA RCU600M... | Answered on Dec 08, 2009

hi i bought a flatscreen samsung and subscribed to sky tv and got the blue ray... how do i get all these to work on one remote insted of three

RCA RCU600M... | Answered on Nov 25, 2009

003,004,006,011,019 027,039,040,041,051,071,083 027,037,050

Hope this helps you out.

Cheers Little Dish Fitter

RCA RCU600M... | Answered on Oct 18, 2009

Try this link below.


Hope this helps you out. If this sorts you out please leave a thumbs up


Little Dish Fitter

RCA RCU600M... | Answered on Oct 07, 2009


Go there,

RCA RCU600M... | Answered on Sep 30, 2009

Toshiba: 018,021,023,071,085,090


RCA RCU600M... | Answered on Sep 18, 2009

I am not sure if this remote is compatible with your tv. To check and see if it is and to view all codes, here is a clickable PDF link that will lead you to the code for the RCA, Model Number RCU600M remote control.

I hope this helps!
- CBR2009



RCA RCU600M... | Answered on Aug 18, 2009

Not finding what you are looking for?
RCA RCU600M Remote Control Logo

143 questions posted

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76177 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Cindy Wells

Level 3 Expert

6048 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

RCA Televison & Video

  • RCA Televison & Video

Most Popular Question

codes program innovage products jumbo

  • Televison & Video