20 Most Recent E-Machines D2046 PC Desktop Questions & Answers


Remove the Outer Case Panel on the side by removing the screws on the back that holds it. Now once one side of the case is removed, look down the front on the metal part of the case. You will probably see the plastic catches or hinges from the face plate, push them in to release them and you can remove the face plate.

E-Machines D2046... | Answered on Apr 12, 2012


did u tried the onboard usb ports back of your system

E-Machines D2046... | Answered on Mar 08, 2011


hi
most power supplys are protected against faults when they are connected to damaged equipment
so it possibly just protecting its self

disconnect everything from the PSU except your MB

try to turn on

if your pc boots ok

re connect everythng else one thing at a time attempting to boot each time

when it wont boot you have found your fault

E-Machines D2046... | Answered on Feb 07, 2009


Look in the manual there is a diagram and pin connections for each wire.

E-Machines D2046... | Answered on Feb 06, 2009


to boot a cd then you must have the bios set to allow it, or tap f12 immediately to intercept boot menu and choose cd. sounds like your drive has a few bad disk sectors.

E-Machines... | Answered on Jan 16, 2019


firstly lets think why a Working pc would no longer BOOT. The boot process then. a pc starts the bios which POST's. this results in ONE BEEP which might be followed by messages(if you get several beeps then they are like morse code long/short and count out an error code). when you get your ONE BEEP the pc is working. when it then HANGS(appears to do nothing) its usually because of either a) the cd drive is duff so disconnect its cables. b) the hard drive is duff so disconnect its cables c) the hard drive hasnt quite died yet but has some very slow sectors and is making the Clackety Clack of the heads recalibrating every few seconds. d) there could be a a gpu card bios glitch and your pc is running but you just have a blank screen. some hints then 1) never start removing parts as that corrupts the CMOS(the battery backed up configuration for your BIOS) so you may need to clear your cmos. 2) never play with the idea of changing ram sticks as people usually end up putting them in any old slot(which may result in a non working pc). make sure a PAIR is fitted in slots 0/2 and a separate matching pair in 1/3 slots not in slots 0/1 which is two half pairs. Other factors. 1) a short circuit. your PSU has built in protection, if the psu fan(inside case of the psu) turns and kicks back and immediately stops you have a short circuit and its cuts the power to avoid a fire/meltdown, which could be caused by high wattage gpu(>60 watts) without its extra power cables fitted or wrongly connected front usb cables or removing a mainboard and fitting it into a new box where the board has its support posts NOT lined up with the holes fro the screws so the post is touching underside of the board circuits. hope some of that helps.

E-Machines... | Answered on Nov 22, 2018


Download a Linux distro to a flash drive or DVD and see how well it runs off that. There's HDD utilities like SuperGrubDisk that can diagnose things.

E-Machines... | Answered on Apr 08, 2017


Unfortunately, without a specific model number for your monitor, this may vary from the manual I am referencing. Just the same, I should say the link should at least have enough similarities to get you out of a scenario mode, and into the custom configurations (that I am assuming you are after).

The steps begin on the bottom of page 5.

http://global-download.gateway.com/GDFiles/Document/User%20Manual/User%20Manual_Acer_1.0_A_A.zip?acerid=634321354437313817&Step1=MONITOR&Step2=FLAT%20PANEL&Step3=E182HL&OS=ALL&LC=en&BC=EMACHINES&SC=PA_6E

If you are using a similar model, clicking on the menu button will bring you in the OSD menu where you can customize the brightness, contrast, etc. Any changes will become a "custom" mode that will effectively take you out of anyone of the scenario modes. I have seen monitors that do not allow much customization (if any) outside of the scenario modes. You may find specifics if you search the monitor model number itself. If you post that information in the comments I can help you find info more specific to your display.

26036777-s3re1a4em3ul4plxlhbwewwp-4-0.jpg

E-Machines... | Answered on May 02, 2016


Could be damaged system files. Insert your XP disc and choose repair. You might be lucky.

E-Machines... | Answered on Feb 24, 2016


Knowing the beep pattern will help diagnose the issue. Power on the computer again and listen for long beeps and/or short beeps. There are other possibilities, but if you just cleaned out the computer, I suspect you might have dislodged a memory stick. Make sure they are seated completely and the white tabs are locked securely in place. The beep code you hear will ultimately help determine where the failure is happening.

E-Machines... | Answered on Aug 12, 2015


try booting to safe mode. by using f8

if that works, try a system restore to a previous date.

if that does not help, then it must be a windows corruption and parallel install or repair install will be needed, it can also be fixed by manual troubleshooting and repairing the files.

E-Machines... | Answered on Jul 30, 2015


it depends if it a pc or laptop you can HBCD 15 OR HIGHER TO CLEAR THE PASSWORD. IF IT IS A CMOS PASSWORD YOU CAN TRY TO CLEAR IT BY TAKING OUT THE CMOS BATTERY AFTER YOU UNPLUG THE COMPUTER OR BY USING THE JUMPER TO CLEAR IT (SOME, BUT NOT ALL).


How to Clear Your Computers CMOS to Reset BIOS Settings

How to Reset Your Forgotten Windows Password the Easy Way

http://www.wikihow.com/Delete-Someone's-Windows-Password

E-Machines... | Answered on Jul 23, 2015

Not finding what you are looking for?
E-Machines D2046 PC Desktop Logo

7 questions posted

Ask a Question

Usually answered in minutes!

Top E-Machines Computers & Internet Experts

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Alun Cox

Level 3 Expert

2679 Answers

Are you an E-Machines Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

E-Machines Computers & Internet

  • E-Machines Computers & Internet

Most Popular Question

replaced dead power supply computer

  • Computers & Internet
Loading...