- Page 3 - Answered Questions & Fixed issues

Holding the button is a forced override of the sensor. Make sure nothing is in the way of the sensor and that they are connected properly. | Answered on Apr 10, 2014 | 54 views


Well not knowing the model of your device i can tell you a few possibility's, If the fridge portion is working well than you either have a defective thermostat, or possibly a defective fan unit in the freer compartment or the condensation drain tube has plugged up and not draining the condensation and the heat exchanger has frozen up.
If you have the make and model of your device you probably can download any and all the service information you need to service your unit.
Are you mechanically inclined and ready to service the unit your self ? don`t forget you kneed the tools to do it as well ?
Let me know

Good luck Falco | Answered on Apr 05, 2014 | 66 views

there is a valve that open and closes as the need for more air flow from fridge to freezer it sounds like it is not working check that out and see if it is working | Answered on Apr 03, 2014 | 63 views

all washing machine are noisy it depend on brand but it is on all specially in small room or space | Answered on Mar 31, 2014 | 51 views

Return to the initial set up procedure. | Answered on Mar 28, 2014 | 23 views

This is a video, How to Remove Fuel Lines ,hope help. | Answered on Mar 25, 2014 | 31 views

I'm sorry, but your product is not shown. I can only suggest what I would do if I had that information. First, I would check the manufacturer's web site, particularly the support page. I would use the model number to search for the owner's manual, user's guide, or installation guide (the latter is usually part of the owner's manual, but some products have them published separately).

If you cannot find the manual on the manufacturer's web site, do a general internet search for the brand name, model number, and the term (manual OR guide). There are some sites that carry these for free, and others that may want a fee to download.

The file will most likely be in .pdf format, so you will need Acrobat Reader installed on your computer to read it. Adobe Adobe Reader free PDF viewer download | Answered on Mar 19, 2014 | 144 views

Hi Marie -

Since you didn't mention the brand and model of your stove - I can only offer general help. The first thing I recommend is that you shut off the power to the stove at the circuit breaker panel. It should be a double-wide 40 or 50 amp circuit breaker. Move the handle to the OFF position and leave it there for 30 seconds or so. Then return the handle to the ON position again. Doing this should "erase" the memory of the stove and reset the electronics. If the problem is not longer an issue - the F3 code should be gone. If it returns, we'll have to do more. That will require knowing the name of stove's manufacturer and model number. Let me know how you make out and if you need more help - provide the info requested and I'll see what else I can do. Good luck! | Answered on Mar 18, 2014 | 55 views

If you failed to regenerate the filter (Back flush with brine) then the water softener will not do its job. Check the brine tank, hoses, and timer. | Answered on Mar 12, 2014 | 76 views

If they were all in the same load, something must have fallen into/got mixed with the load, such as ink pen, etc. Full washer with hot water and add cleaning agent such as ammonia or plain detergent to clean the washer cycle.
To clean those shirts, add a 1/4 c of "Simply Green" / The Green Stuff ($ store brand) to temp appropriate water, directly spray on spots and let soak a few minutes, then wash (with or without detergent) and do a double rinse cycle. Naptha or Zote laundry BAR soap are good as "detergent". HTH | Answered on Mar 06, 2014 | 67 views

First thing I\'d do is inspect the hose. Remove it from the washer entirely (use a bucket to contain stray water) and visually inspect / wash out with a water spray nozzle like a garden or kitchen hose. From the sounds of it, however, I doubt the hose is the issue, but you\'ll want to rule that out first.

If the hose checks out, then either the pump or the belt is the issue. Pumps tend to get clogged over time--I\'m not familiar with yours, but yours may be able to be opened (if so, it\'ll have screws holding it together) and you can remove it and clean it out. If it\'s clogged and a sealed unit, you just get a new pump.

If the pump looks ok, the belt might be slipping, but if that were the case you\'d probably have more issues. Still, depending on the age of the unit, you may want to replace the belt now since you\'re going to have to remount the belt after playing with the pump.

I use repair clinic for my guides while doing work, and if I can\'t find the part locally I use them to supply the parts. Check out this page for more help: Whirlpool Washer Won Drain . Of course, if the idea of taking apart your washer totally freaks you out, go hire a repair person. :) But they\'re not all that hard, honestly--more of just a pain to take care of, since this\'ll probably be your first washer tear-down. Best of luck, and watch those videos at repair clinic--they\'re pretty helpful! | Answered on Oct 07, 2017 | 213 views

one of two things. the hoses are connected backwards or the valve on the hot hose is closed. i guess it could also be the water heater not working. | Answered on Mar 04, 2014 | 30 views

There is some interference created by other wireless devices within range of your garage door. This maybe a door bell, baby motor or car immobilizer. Check to see if there are any new wireless devices, it maybe someone Cole by like a neighbor. Alternatively, you can delete the existing remotes from the unit and reprogram the remotes again, this will reprogram the emotes on a different frequency and hopefully cut out any interference. Need new garage roller doors for your Perth home Think Modern Garage... | Answered on Feb 27, 2014 | 118 views

First, ice build up may be keeping the arm from dropping. Manually push it down, but do not force it. If it comes down, turn your freezer to as low as you can.If it does not come down. Remove all the frozen food and turn the freezer to the warmest setting and let it thaw. The arm then should be able to be pulled down. Then turn the freezer to the coldest setting for ice. It that doesn't work, you probably need a new water valve. | Answered on Feb 22, 2014 | 54 views

What the heck it this garbage about washers | Answered on Feb 12, 2014 | 212 views

Not finding what you are looking for? Logo

544 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Computers & Internet Experts


Level 2 Expert

89 Answers

Brad Brown

Level 3 Expert

18136 Answers

Paul Bade

Level 3 Expert

1662 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides