Top 20 Ademco 6137b Fixed English Keypad Vista Systems Questions & Answers


Best bet would be to try and contact the prior owner and ask for it! Should have left such instructions for you as part of the sale/exchange. Just try asking if it's possible to do so.

Ademco Home... | 69 views | 0 helpful votes


Within 30 seconds of power up press *and # simultaneously. Display should say 20, if you press *20 1234 then *99 to exit programming. Your system should be disarmed and your install code should now be 1234. You can then use this code to change the master code.

Ademco Home... | 273 views | 0 helpful votes


multiple low battery ones in sequence , mean a remote low battery. There is usually only one reporting zone on the remote (panic). That would be why only one zone shows alarm.

Ademco Home... | 398 views | 0 helpful votes


It should (If installed correctly) be hard wired to a fused unswitched outlet fairly local to the control panel, if that is the case remove the fuse and then the wire to the control panel.

If not you may find it is wired directly to your fuse box, a wall socket or even a ceiling rose. an electrician will easily be able to trace it's source.
An indication as to where it is wired can be obtained by switching/pulling each fuse/mcb in turn untill the control panel powers down.

Ademco Home... | 286 views | 0 helpful votes


You will need to add an Alarmnet wireless communicator device and subscribe to Total connect to interact with a smart phone.

Ademco Home... | 385 views | 0 helpful votes


learn the two into the Code Encryptor receiver by pressing and releasing the black button on the receiver. The red light on the receiver should come on. press and release the closed padlock button 3 times, the red light on the receiver should go off

Ademco Home... | 124 views | 0 helpful votes


The key for the panel is supplied from the distributor and you need to be a certified installer to open an account and buy one, A good old big flat screw driver will open the pannel as well but the lock will be useless after that LOL! (you could screw the dore shut with #6 sheet metal screws after) than you can go on the Ademco's web site to serch for the default code of your alarm panel model but if the installer changed it than you have to reset the panel to factory default and re-program it... (unless the installer activated the installers lock up) than you need the code from the last installer that serviced the panel... if not than you need to send the board to Ademco to have it unlocked or change the board for a new one... (you will still have to re-program everything from scratch...

That's what security is all about!!! $$$$

THE BEST WOULD BE CONTACTING THE LAST INSTALLER FOR SERVICE...

Ademco Home... | 1,131 views | 2 helpful votes


Hi, well i suspect that when the power went either out, or more likely when service was restored, the device suffered a "Power Spike, Surge, or Transient" This is an all to common thing, most people do not know how imperative it is to UNPLUG ALL electronic equipment, after the power outage, and only connect a little time AFTER re-connection to avoid any "Nasties" that will occur at the time of and soon after power is reconnected to the grid. Sensitive electronics can and will be damaged by these events as has been evidenced here.
Most likely the power supply unit is damaged, however it may indeed have gone "Deeper' into the electronics without examination one simply cannot tell.
In, my experience, over the many years, these instances i cannot recommend repair, as most often, the very damage done is of a nature that precludes repair, and demands replacement only.
A surge or spike buster device may, assist and are a worthwhile addition, and should always be used regardless on electronics connected to the Mains, however ALWAYS remove totally the connection, in future instances of power outages, to stop this from occurring again.

Ademco Home... | 203 views | 0 helpful votes


The resolution depends on the code being shown on the keypad. The first two things that come to mind are 1> The control panel's backup battery is low and not accepting a change and needs replaced, or 2> If the code on the keypad shows 'BF', this is Backup Failure, and it means that your backup communications device, such as a GSM Long Range Radio, is not functioning. If you see this code on the keypad, immediately call your local alarm company for a fix. If your communications are down, police / fire / ems will not be dispatched in the event of an alarm.

Ademco Home... | 725 views | 0 helpful votes


Wooden flooring is known for its elegant look. It creates a warm ambience inside your home. Hardwood floors are elements of d?cor themselves, which are available in many different types and colours. Its durability will ensure a good interior investment while providing aesthetics to your home.

Home Security | 19 views | 0 helpful votes


The RED "H" is an error with the hard drive on your recorder. There is no easy fix. You will have to refer to a technician/ repairman.

Home Security | 25 views | 0 helpful votes


Be sure the safe door is held in tightly enough for the sensor to register it is in the right position for the lock to engage when you are pressing the "close" key sequence.

Home Security | 56 views | 0 helpful votes


Red plus 12v
yellow video output
screen bare wire 0v and video earth

Home Security | 74 views | 0 helpful votes


Go to a locksmith. Bring lots of money.

Home Security | 57 views | 0 helpful votes


Did you reset it? If not try a reset this will usually fix the issues with those types of doorbells.

The reset option is under the face plate.

Home Security | 46 views | 0 helpful votes


try to find it on youtube u can get step by step guide other option is calling on Arlo Support Number(+1-844-919-1777). i hd same issue bot now its work fine

Home Security | 65 views | 0 helpful votes


Order it from Protector

Home Security | 60 views | 0 helpful votes


Contact Gordon directly to inquire.

Home Security | 64 views | 0 helpful votes

Not finding what you are looking for?
Ademco 6137b Fixed English Keypad Vista Systems Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Ademco Home Security Experts

Brad Brown

Level 3 Expert

18127 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

Are you an Ademco Home Security Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ademco Home Security

  • Ademco Home Security

Most Popular Question

while programming one keypad ademco 6151

  • Home Security
Loading...