20 Most Recent Ricoh Aficio AP3800C Laser Printer Questions & Answers


1. ATTACHED PRINTER TO COMPUTER AND TURN IT ON
2. OPEN PRINT PROPERTIES
3. CLICK ON SMART ORGANISER, IF U DO NOT HAVE THIS DOWNLOAD AND INSTALL FROM RICHOH WEBSITE
4. CLICK ON ABOUT
5. MOVE MOUSE ARROW KEY TO PICTURE ABOVE TEXT BOX INSIDE BLUE AREA
6. HOLD SHIFT AND CONTROL KEY AND DOUBLE CLICK RIGHT MOUSE BUTTON TO OPEN SERVICE MENU
>>>>> DO NOT PLAY WITH ANY OTHER SETTING OR YOU MAY PERMANENTLY DAMAGE UR PRINTER<<<<
7. CLICK ON RESET SC FUSE ONCE ONLY. (IT WILL BE SECOND LINE TOP LEFT SIDE)
8. FROM MAIN POWER SWITCH TURN POWER OFF AND AFTER 10 SECOND TURN IT BACK ON.
9. UR PROBLEM WILL BE SOLVED.

Ricoh Aficio... | Answered on Jun 25, 2019


To reset error, enter SP mode by pressing: Clear (yellow) button, 1 0 7, and press and hold the Stop (orange) button for 3 seconds then switch off and on the copier.
If the error is still there, please check the following in the fuser unit;
  • Check and clean or replace the possible defective thermistors or out of position.
  • Fusing heaters open circuit.
  • Thermostats for open circuit.
  • Power supply unit.
Good luck and please rate me, thanks.

Ricoh Aficio... | Answered on Dec 10, 2018


YOU NEED TO PRESS C BUTTON(RED) LATER PRESS KEY 1 , KEY 0 , KEY 7 & HOLD THE YELLOW KEY FOR SEVERAL SECONDS, THEN THE MACHINE WILL ENTER SP MODE

Ricoh Aficio... | Answered on Oct 16, 2018


Its an over load of information by the file.
here is the actual code: SC670 mistake Engine Response

Ricoh Aficio... | Answered on Sep 26, 2018


Hold down the two arrow keys and count to 5, hit the enter key, the machine should be in serrvice mode if nor repeat. use arrow ke and scroll to machine press enter scroll to data log press enter scroll to pm counter reset presss enter, scroll to fuser oil press enter and exicute this mod Please. DO NOT GO INTO ANY THING ELSE or you could do serious damage to your machine!! If your machine has a Copy feature expander yopt must press Clear mode, Press 1-0-7 and then hold down the stop cancel key 4sec. go into copy sp mode press 7-804-809 press exicute button again Please DO NOT GO ANY WHERE ELSE as damag can be done to your machine. Hope this helps!!

Ricoh Aficio... | Answered on Sep 02, 2018


I am a Ricoh tech and my service manual doesent have a 300 code,

Ricoh Aficio... | Answered on Jul 16, 2017


Replace pump with new one. When this happens problem with rubber worn out

Ricoh Aficio... | Answered on May 03, 2017


turn the printer off and reinstall the unit after it has cooled off (30 minutes). Then open cover B and D. Remove the fuser unit, then reinstall it properly. Close covers D and B. The error clears automatically if the fuser unit is properly installed.

If the error is not cleared, the fuser unit is out of order. Replace it with a new fuser unit.

Ricoh Aficio... | Answered on Aug 01, 2016


Thats a fuser error. Thermistors needs to be replaced. Alternatively you can try clearing the code in sp mode push yellow button 107 and hold red button. Select 1 and the 5 (mode) then clear scs.

Ricoh Aficio... | Answered on May 29, 2015


To reset fuser SC codes you need to enter Service Programme Mode and reset SP5-810 to 1, then turn the main switch off and on again. If you need help on entering SP mode etc. then take a look here.

Ricoh Aficio... | Answered on Mar 28, 2015


sc300 on a Ricoh 2060 is a corona wire error. Typically what happens is the corona wire has snapped, and a new wire needs to be installed.

Ricoh Aficio... | Answered on Aug 01, 2014


PLEASE ENTER THE SP MODE AND THEN PRESS 5801 TO ENTER THE FRMATTING MODE .
SELECT FORMAT HDD AND EXECUTEE.
THANK YOU.

Ricoh Aficio... | Answered on Jul 23, 2014


SC542 is a heating roller warm up error. Most likely the fuser lamp has failed - a faulty sensor or board is also possible but not very likely. You'll need a new fuser, I suspect.

Ricoh Aficio... | Answered on Jun 10, 2014


Enter service mode (hold down up/down for 5 seconds then hit #) service mode 5-810 to reset (fuser problem)

Ricoh Aficio... | Answered on May 09, 2014


SC389 is a development gamma error in the magenta. There can be several causes for this error - a toner supply problem, incorrect toner used, a laser exposure problem etc. This is not likely to be an easy problem to fix unless you are experienced in such matters, so you may need to look for someone who can help out.

Ricoh Aficio... | Answered on Mar 28, 2014

Not finding what you are looking for?
Ricoh Aficio AP3800C Laser Printer Logo

276 questions posted

Ask a Question

Usually answered in minutes!

Top Ricoh Office Equipment & Supplies Experts

gggg

Level 3 Expert

904 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

quennie732

Level 2 Expert

422 Answers

Are you a Ricoh Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Aficio Ricoh

  • Aficio Ricoh

Most Popular Question

fix ricoh afico sp 100 sc542 error

  • Office Equipment & Supplies
Loading...