Honeywell FocusPRO 6000 5-1-1 Day Programmable Thermostat - TH6220D1002 - Answered Questions & Fixed issues


To change to F to C follow the next steps:

1. Press and hold and the same time (simultaneously) the up arrow and fan button (middle button under the screen) until the display changes.
2. Press next until you see 14 on the left and 0 on the right.
3. When you see the 14 on the left and the 0 on the right, press up arrow to change number 0 for a 1.
4. Then press Done and you will see your normal display in Celcius.

Good luck!

Honeywell... | Answered on Jan 23, 2020 | 49 views


What type of system do you have?
If you have a heat pump with a reversing valve you will need to set the thermostat settings for a heat pump. Or it can also be the wiring. Check your setting on the thermostat.

Honeywell... | Answered on Jan 23, 2020 | 123 views


The TH8320U1016 thermostat has 2 terminal pins "S1 and S2" that are the ones that are connected to your outdoor sensor, but the TH9320WF003 it doesn't have the "S1 and S2" terminal pins, so I would recommend you the TH6320WF2003 this thermostat is compatible with all system types and with outdoor sensors terminal pins "S1 and S2".

Honeywell... | Answered on Jan 23, 2020 | 41 views


Did you set the minimum and maximum settings on the thermostat?
When they come new the settings are set to about the same temperature.
One must set the upper and lower temperatures manually....

Regards
Geoff

Honeywell... | Answered on Jan 06, 2020 | 43 views


https://www.manualslib.com/manual/576182/Honeywell-Th2110dv.html?page=5#manual

Honeywell... | Answered on Jan 03, 2020 | 30 views


go to honeywells website and download the manual for it

Honeywell... | Answered on Dec 30, 2019 | 34 views


means its getting power check thermostat to see if calling for cooling or heat

Honeywell... | Answered on Dec 18, 2019 | 51 views


call a good local repair service we do not recommend any diy fixes for gas appliances due to liability issues

Honeywell... | Answered on Dec 16, 2019 | 49 views


Thermostats have multiple issues when you start checking them against thermometers.

1) the built-in thermometer may not match the set temperature because one or both need calibration. Compare the built-in to an external thermometer and see if there is any adjustment to make them match. Record the setting on the thermostat and the temperature when it starts and stops -- there should be a 1-3 degree range which may be adjustable. The set point should be in the middle of the on-off temperature spread.
2) the thermostat has a heat anticipator setting which may be set poorly -- turning off the heat before it reaches the set point - the fan normally runs for 1-2 minutes after the heat source is off. The anticipator is used to stop heating before reaching the set point as there are still a lot of BTUs coming out during the fan run-down -- usually 1-2 minutes.

Honeywell... | Answered on Oct 16, 2019 | 61 views

Not finding what you are looking for?
Honeywell FocusPRO 6000 5-1-1 Day Programmable Thermostat - TH6220D1002 Logo

7 questions posted

Ask a Question

Usually answered in minutes!

Top Honeywell Heating & Cooling Experts

Bill Long

Level 3 Expert

606 Answers

Paul Carew

Level 3 Expert

3492 Answers

Cindy Wells

Level 3 Expert

6073 Answers

Are you a Honeywell Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...