20 Most Recent Whirlpool Whirpool 3.5cu ft Top Load Washer w/ Questions & Answers


  1. Turn the washer off.
  2. Set the mode selector dial to NORMAL.
  3. Turn the dial counter clockwise ONE click (LEFT), clockwise THREE clicks (RIGHT), counter clockwise ONE click (LEFT) then clockwise ONE click (RIGHT).
  4. Now press the start button.
  5. All the cycle indicating lights should be illuminated.
  6. Press the Start Stop button once.
  7. Rotate the dial until Rinse, Wash, and Stop light illuminate.
  8. Turn the washer off and unplug it for 10 seconds.
  9. Finally, turn on the washer and it should now be reset.
  10. Run a test load empty to be sure the reset worked. If not perform the reset procedure one more time.

Whirlpool... | Answered on Oct 07, 2016


Depending on model there not much, I usually hot wire mine..just take the switch off and connect the wires together with a wire nut...

Whirlpool... | Answered on Nov 20, 2014


Sounds like the vent is plugged up, that's a fire hazard take it apart and clean it out..

Whirlpool... | Answered on Nov 20, 2014


It is possible that the replacement water level switch is defective.

Whirlpool... | Answered on Jun 20, 2014


Hi, there. While we cannot assist with repairs I can offer links to our troubleshooting, use and care guides, replacment parts, parts lists, and service line should that be necessary. We hope this helps.
http://bit.ly/zkfnZd
http://bit.ly/112Lu7q
http://bit.ly/LrNZiS
http://bit.ly/yLv4Z5

Whirlpool... | Answered on Feb 07, 2014


1.), Pump may be bad. Check voltage to water pump in Spin Cycle. If you have voltage at the pump, but it does not run, replace the pump.

2.) If you have voltage to the water pump, and can hear or feel it running, cut power off, and remove the boot which is directly below the wash bin. The boot empties into the water pump. You will need long needle nose pliers or better, use water pump pliers to remove the straps holding the rubber piping to the pump and the boot. Remove debris from the boot, i.e., bobby pins, coins, socks, pens, keys, etc.

3.) If no voltage comes to the pump in spin cycle, you may need a new timer.

4.) Install a new belt on the motor pulley. You will regret not replacing the belt later.

Whirlpool... | Answered on Feb 03, 2013


My first suspect is the thermocouple has failed (they should be changed periodically, every 5-7 years as they do fail). Without the signal from the thermocouple, the gas valve can not open and start the ignition process.

Whirlpool Water... | Answered on Jan 18, 2020


Whirlpool sold the AO Smith brand flue damper, and the atmospheric models ... both models have different honeywell gas controls...
Error codes, service manuals and troubleshoot appear following link:
http://waterheatertimer.org/How-to-troubleshoot-gas-water-heater.html#honeywell

There is no specific service manual available for the flue damper series in 2019

Whirlpool Water... | Answered on Nov 10, 2019


6 flashes is typically found with power vented and flue damper type heaters ... whirlpool never sold a power vent, but they did sell the AO Smith brand flue damper series heater.
The following manual suggest the problem is either gas supply or pilot assembly.
http://waterheatertimer.org/pdf/Power-damper-troubleshoot-parts-manual.pdf

More resources on following link:
http://waterheatertimer.org/How-to-troubleshoot-gas-water-heater.html#honeywell

Whirlpool Water... | Answered on Nov 04, 2019


it is a WATER HEATER. you do not need to heat HOT water.
Gas or electric?
Electric = turn power on
Gas = instructions are on gas valve or in your manual.
does not light = verify a spark at burner when you push button (can be hard to see, turn off lights), verify gas valves are on and another appliance has gas, call for service.

Whirlpool Water... | Answered on Sep 05, 2019


there is none on it now 14 years ago was too long . plan on a new one quick

Whirlpool Water... | Answered on Mar 28, 2019


Water heaters only have a top and bottom thermostats which seldom go bad. Heating elements wear out most often. If you are running out of hot water too quickly kill the power drain the tank and remove bottom heating element using a special large socket. Visual inspection should tell you if it is melted. If it is ok check the top heating element. If the heater was on and the tank not full the top element will go first. Elements never operate at the same time

Whirlpool Water... | Answered on Mar 21, 2019


CONTROL PANEL LOCK - Holding this button for more than 3 seconds switches the lock mode on or off. When the User Module is locked, a symbol and "Lock" text will be visible on the display.

No model posted, so used the following energy smart
http://www.whirlpoolwaterheaters.com/media/123507/318686.pdf

Whirlpool Water... | Answered on Mar 04, 2019


POSSIBLY TRIPPED THE BREAKER IN MAIN BOX

Whirlpool Water... | Answered on Jan 02, 2019

Not finding what you are looking for?
Whirlpool Whirpool 3.5cu ft Top Load Washer w/ Logo

28 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Water Heaters Experts

Thomas F. Schneider

Level 3 Expert

2715 Answers

jdthefixer

Level 3 Expert

746 Answers

Mike

Level 3 Expert

4369 Answers

Are you a Whirlpool Water Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Whirlpool Water Heaters

  • Whirlpool Water Heaters

Most Popular Question

top load whirpool washer restart its own

  • Water Heaters
Loading...