Top 20 Tomtom GO 700 GPS Receiver Questions & Answers


First, make sure that your TomTom battery is (fully) charged. Then press the ON/OFF power button ... to turn it on. If it still doesn't turn on, try to RESET it ... using a "pin" (e.g. paper clip) to push up the RESET hole at the bottom of the device.

Tomtom GO 700... | 70 views | 0 helpful votes


What version of Eastern Europe

Tomtom GO 700... | 181 views | 0 helpful votes


settings/user
delete and leave blank every page, just click done and restart

Tomtom GO 700... | 1,093 views | 0 helpful votes


Batteries on the START series of tomtoms are not brilliant.
Replace the battery
compu-sat.co.uk

Tomtom GO 700... | 31 views | 0 helpful votes


It may help if you regularly get the latest satellite positions (for the next 7 days) - QuickGPSfix data (via TomTom HOME).

Tomtom GO 700... | 161 views | 1 helpful votes


Route will not plan until the GPS is locked.
Soft reset on the button underneath for 30 seconds will reset the GPS receiver on a 700.
Then wait upto 4 minutes for a refreshed lock after power up

Tomtom GO 700... | 100 views | 0 helpful votes


It may be likely that the TF (SD) card is not being read properly or has been damaged/corrupted.
Try to read that SD card on your computer (i.e. not using the GPS) ... and see if it works. And/or use the Properties - Tool - Check Disks tool to "recover/fix" the SD card (on your PC).

Tomtom GO 700... | 62 views | 1 helpful votes


Posting with them is a good thing, they know their system better than anyone else...good luck.

Tomtom GO 700... | 153 views | 0 helpful votes


Hello
Here is some more information for you to follow to guide you step my step. Device displays a white or red cross
If your navigation device displays a cross after you switch it on, it means that the TomTom application is not installed correctly.
Note: It is normal for the navigation device to show a cross while it is connected to the computer.

The solution depends on which TomTom software is used for updating. Check which software your navigation device uses for getting updates.
Devices using MyTomTom for updates
For navigation devices that use MyTomTom, reset your device.
Devices using TomTom HOME for updates
For navigation devices that use TomTom HOME, you can solve this problem by installing the latest application on your navigation device.Here is also a link that will help you more. This will answer all your questions Mike
http://www.tomtom.com/support/index.php?Language=1&query=red+cross&FID=1898

Tomtom GO 700... | 316 views | 1 helpful votes


write to me: service@gps.pol.pl I will try to help

Tomtom GO 700... | 162 views | 0 helpful votes


Try to do a "Boot" .... by pressing and holding down the ON/OFF button for 5 seconds (or a lot more) until the device powers on again. Yes, at times, it may take a minute or more ! of holding that button down.

Tomtom GO 700... | 80 views | 1 helpful votes


To reset your TomTom device, do the following:
  1. Check that the battery is charged properly.
    Charge your device for at least 2 hours before trying to turn it on again. Make sure the charging light on your device is on.
  2. Remove the SD card
    If your device uses an SD card, remove it.
  3. Reset your device.
    Use a straightened paper clip, or something similar, to push the reset button for at least 20 seconds. The reset button is a hole at the base/bottom of the device.
  4. Turn your device on.
    Press the On/off button for at least 5 seconds or more, until the GPS starts up. It may take a minute or two of holding it down.
  5. Insert the SD card
    If your device uses an SD card, insert the SD card.

Tomtom GO 700... | 47 views | 1 helpful votes


Welcome to Fixya

Please follow this procedure. Go to change preferences, then to safety preferences, chose either enable safety lock or disable safety lock. Hit done then choose to turn off map display , never or above a certain speed or always. hit done.

Thank you for using Fixya!


If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

Tomtom GO 700... | 128 views | 0 helpful votes


Glad to HELP YOU!

Reset your device by pressing a straightened paper clip into the reset hole on the bottom of the unit behind the release button.

Hope it will help you!
My best wishes!

Tomtom GO 700... | 465 views | 0 helpful votes


tom tnm go 4v00.710 wont start after charge

Tomtom GO 700... | 1,897 views | 0 helpful votes


Sounds like you tried to upgrade and something went wrong.
If there is a reset button on the bottom or back that'll be your best bet. The red X means it cannot find the operating system but usually a hard reset will fix it.

Tomtom GO 700... | 130 views | 0 helpful votes


When your tomtom is flashing a red cross on it, then it means there is a problem with the unit. The problem mainly is that the device did not start up properly. And that is because it did not find the application.
What you have to do is to reset the device for it to start working again. For your type of tom tom, to reset it, to reset it.
Check that the battery is fully charged or you charge it for about 2 hours, remove the SD card, then straighten a paper clip or something similar to push the reset button, then you press the on/off button for about 5 seconds to power on the device then you insert your SD card. The reset button is at the bottom of the device where you have the USB connection port.
Hope this was helpful. Thank you for using fixya.

Tomtom GO 700... | 407 views | 4 helpful votes


The moment you connect your TomTom device to a computer, your device should ask Do you want to connect to 'computer'. Once you tap YES, it should connect to the computer. TomTom HOME then starts.

If your device is not connecting, click one of the solutions below:

Tomtom GO 700... | 566 views | 0 helpful votes


Ok, there are a couple of options that may or may not work. The problem with TomTom units is that they do not like being used with universal chargers and sometimes they can be damaged when using one. The hard disk drive inside them in particular is very sensitive.

Try these options first before thinking about having the unit repaired -

Try holding the reset button for anywhere between 1 and 20 seconds.

Try holding the power button for at least 3 seconds

Lastly hold down the reset button for 10-15 seconds and then while holding the reset button, press the power button and hold that for around 5-10 seconds.

If you are unsure of where the reset button is, here is an image showing its location -

overlode_0.jpg
If none of the above steps work then it is highly likely that your unit has suffered damage that needs to be repaired by a specialist.

I hope this helps and thank you for using FixYa

Tomtom GO 700... | 409 views | 1 helpful votes

Not finding what you are looking for?
Tomtom GO 700 GPS Receiver Logo

295 questions posted

Ask a Question

Usually answered in minutes!

Top Tomtom GPS Experts

LP

Level 3 Expert

514 Answers

k24674

Level 3 Expert

8081 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Tomtom GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GO Tomtom

  • GO Tomtom

Most Popular Question

flashcard not loading

  • GPS
Loading...