Mintek Portable DVD/CD Player w - Answered Questions & Fixed issues


Hello
Try these links to download the user manual to your device. If you feel any difficulty in downloading the same, inform me your email address. I'll send a copy of the manual to you by return mail.
http://documents.knowhow.com/TV-Home%20Entertainment/L9SPDVD11_IB.pdf
http://www.dataentryjobs.us/67948.html
http://www.shopwiki.co.uk/l/DIV99R-Portable-DVD-Player-9%22-%2823cm%29-screen%2C-MPEG~4-DTT%2C-USB

Mintek Portable... | Answered on Mar 03, 2012 | 927 views


If jiggling the lid switch causes the picture to show dimly, the switch may have bad contacts.

Can you see the picture if you shine a flashlight or lamp on it at an angle? If so, your problem is specifically the display backlight (including perhaps the lid switch in the circuit). If it uses Cold Cathode Fluorescent Lamps (CCFL), the CCFL tubes may be going bad, and jiggling the lid switch is having the same effect as multiple flips of a light switch to start up weak fluorescent light tubes. If the screen has a pinkish tinge or the light flickers a lot, that's another indicator that a bad tube is your problem. A replacement CCFL is probably about $8-$10, but the replacement requires some disassembly and highly skilled solder work (you have to make a physically small connection, and you can't have heat on it for more than three seconds at a time).

Mintek Portable... | Answered on Jul 09, 2011 | 118 views


Problems often occur on the DVD / CD player is on the motor, optic cable, and optical konponen weakened.
Try changing the motor first, then optic cable and the last one is optic.

Mintek Portable... | Answered on Jun 20, 2011 | 195 views


http://www.amazon.com/Dvd-1710-Dvd-5820-Dvd-5830-Dvd-5861-Mdp-1810kit/dp/B001T89882/ref=dp_cp_ob_e_title_0

$9.00

Mintek Portable... | Answered on Jun 01, 2011 | 79 views


The motor probably froze up over time. You need to put a disc in and spin it with your finger around in the direction it normally turns in play mode. Do that for a while and then see if it will do on it's own.

Mintek Portable... | Answered on May 29, 2011 | 36 views


Radio Shack has a replacement adaptor for the Xacti VAR-G9,
You need the following 5V DC (Five Volts Direct Current) 2.0A   (Minimum 2.0Amps - more is OK, less is not)
The TIP is positive.
The unit I purchased from RadioShack is P/N273-1696 and works great for my Xacti.
Make sure you don't have any little kids who may change the switch setting from +5V to something larger.
Also pay CAREFUL attention to the TIP  voltage on the adaptor. The Sanyo takes a + Tip.  
There are other cheaper solutions as well, but this unit can be re-used with other gadgets.
My Sanyo VAR-G9 AC adaptor failed after TWO DAYS out of the box, so I can't recommend buying a Sanyo VAR-G9, until Sanyo fixes their manufacturing problems with the units.
--Ross

Mintek Portable... | Answered on May 13, 2010 | 3,712 views


be more specific please...

Mintek Portable... | Answered on May 31, 2009 | 103 views


Looks like the power board in the device is defective. Best suggestion (and cheaper option) would be to simply buy a new portable..

Mintek Portable... | Answered on May 29, 2008 | 140 views


Qtip , alcohol and acetone ? I am almost sure that you have already ruined the lens. In many of the CD or DVD players that I have repaired, the problem is the degradation of the power of thelaser. Im computer drives there are cases that I was able to fix the porblem by adjusting the power of the laser. this is quite dificult as the trimmer potentionmeter is very small and most often very hard to access. Usually this trimmer is located in the laser assembly.. Another dificulty is that the adhustment should be procise, too much power will also not work. My success rate of this procedure is only about 50-70 % But because you already cleaned it with Qtip, maybe the lens are no longer aligned and because of the alcohol and acetone, the lens may not be clear anymore.

Mintek Portable... | Answered on Jan 28, 2008 | 182 views


If it has the RCA (Red,White,Yellow) ports you will have to use those. In that case if you are using something like a DVD player that only has HDMI output you will need a special cable that goes from RCA to HDMI. Here is a quick link for you to reference.
https://www.walmart.com/ip/5-Feet-1-5M-1080P-HDTV-HDMI-Male-to-3-RCA-Audio-Video-AV-Cable-Cord-Adapter/965878335?wmlspartner=wlpa&selectedSellerId=11827&adid=22222222228252900294&wl0=&wl1=g&wl2=m&wl3=296348219694&wl4=pla-526929718011&wl5=9010172&wl6=&wl7=&wl8=&wl9=pla&wl10=117084777&wl11=online&wl12=965878335&wl13=&veh=sem

Mintek Televison... | Answered on Jun 11, 2019 | 25 views


It means you're on comp1 input. Change the input to whatever you are connected to

Mintek Televison... | Answered on Mar 10, 2019 | 28 views


Google (mintek)(mdp-1810)(manual) without parens.

Mintek Televison... | Answered on Aug 30, 2018 | 151 views


It has an HDMI socket at the back for connection of the blue ray.

There is a manual for the model

Mintek DTV 265 Owner Manual

Mintek Televison... | Answered on Jul 06, 2018 | 118 views


The could would be found in a compatible remote control.

Mintek Televison... | Answered on Jan 25, 2018 | 324 views

Not finding what you are looking for?
Mintek Portable DVD/CD Player w Logo

18 questions posted

Ask a Question

Usually answered in minutes!

Top Mintek Televison & Video Experts

Ekse

Level 3 Expert

13434 Answers

Brad Brown

Level 3 Expert

18157 Answers

The Knight
The Knight

Level 3 Expert

76204 Answers

Are you a Mintek Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...