20 Most Recent Fisher and Paykel 23 in. DD-603 Built-in Dishwasher Questions & Answers

Tip

Determining the Age of Your Fisher & Paykel Appliance


This advice applies to Fisher and Paykel appliances. Determining the manufactured date of most appliances is accomplished by looking at the SERIAL NUMBER. On Fisher and Paykel appliances this is determined by the by the 1st two letters of the serial number.

The 1st letter represents the YEAR of manufacture.
The 2nd letter represents the MONTH of manufacture.

Example: DHL121796


LETTER YEAR

C - 1
U - 2
M - 3
B - 4
E - 5
R - 6
L - 7
A - 8
N - 9
D - 0

LETTER MONTH

F - 1
I - 2
S - 3
H - 4
E - 5
R - 6
P - 7
A - 8
Y - 9
K - 10
U - 11
L - 12

In this example the appliance was manufactured in April of 2000.


on Jan 17, 2019 | Fisher and Paykel 23 in. DD-603...


We had this problem a few days ago. We called a repairperson, who recommended unplugging the unit, then replugging. It seemed to reboot it — closes as it should and works fine.

Fisher and... | Answered on Dec 22, 2018


Hello!

Please check the manual to this dishwasher. Hope it will help!
https://manualsbrain.com/en/manuals/1261053/?page=12

Fisher and... | Answered on Oct 24, 2017


If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/
Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Fisher and... | Answered on Dec 04, 2015


The flood switch is accessed by removing the bottom drawer. The flood switch cover is removed by sliding to the right. There is a release clip underneath about mid point of the cover.

Fisher and... | Answered on Feb 22, 2015


Yes it would be in the drying cycle which goes for almost an hour after the final rinse

Fisher and... | Answered on Oct 03, 2014


Manufactured date is on label attached to washer.

Fisher and... | Answered on Jun 15, 2014


F1 error means flood switch at base of dishwasher under bottom drawer has been set off. This is due to water leakage.
Unsure why the vibration is occuring. Can you please confirm by adding some information in the comments field if the F1 is displayed on both drawers or just one and which one.

Fisher and... | Answered on May 25, 2014


ok , F1 means your flood switch has activated, which is underneath the drawer. now they show the F1 fault because of 2 reasons.1st there is still water underneath drawer causing switch to activate. 2nd your activator board which has the flood switch attached is faulty reading your posting it has been about 15 days since the fault happened. the water should have dryed around switch by now. if there is power to the unit and it is still coming up with F1 fault then possibly you have damaged the activator board. please reply and tell me if you have power on or off at the present time. to fix the problem it is alittle bit involved but i can guide you thru it when you reply .good luck

Fisher and... | Answered on May 24, 2014


manufacture does not reccomend using tabs, small amounts of powder, will work jsut fine

Fisher and... | Answered on Apr 14, 2014


It is very unlikely the inlet water hose is blocked. Most likely it has thinned out and needs replacement. You will have to take the bottom drawer out to get to it. Make sure the diswasher is disconnected from mains power and the water inlet under kitchen sink is shut. The plastic plugs on each side needs to be pulled out to get the front cover out and access the slide rails on which the drawer slides. Make sure the front cover does not fall as the controller and panel are held in it. Take the tub out and leave on floor. The water inlet valve and inlet hose are mouned at the back wall of housing.

Fisher and... | Answered on Apr 13, 2014


This is a controller fault and depending on the conditions of when it occured, may need replacement of controller itself or some sensor which feeds signal to the controller. Usually if fault keeps repeating or is permanently on and turning mains power off and on makes no difference, then you will need a technician to look at it.

Fisher and... | Answered on Apr 13, 2014


This is a serious problem. Most likely the base of drawer is leaking. This contains the motor and heater units. Refer this diagram.

http://spares.bigwarehouse.com.au/images/files/18816_a21ebb5ac093d66472cef9bd1e8f3b12

Fisher and... | Answered on Apr 03, 2014

Not finding what you are looking for?
Fisher and Paykel 23 in. DD-603 Built-in Dishwasher Logo

209 questions posted

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Dishwashers Experts

Mark Davis

Level 1 Expert

18 Answers

Bruce Denton

Level 2 Expert

273 Answers

Paul Bade

Level 3 Expert

1662 Answers

Are you a Fisher and Paykel Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Fisher and Paykel Dishwashers

  • Fisher and Paykel Dishwashers

Most Popular Question

wont start

  • Dishwashers
Loading...