20 Most Recent Fisher and Paykel 24 in. DD603H W Built-in Dishwasher - Page 4 Questions & Answers


The problem is with rotor assembly of the drawer that is causing the F2 error. Turn power off. Empty water using a small container and towel to dry base.


Remove the washer arm and drain filter sump cover. Twist the rotor at the base out from the socket gently but firmly.
Clean the cavity and check the rotor for damage. Put everthing back in and turn power on.If F2 does not go away then replace rotor.

Fisher and... | Answered on Aug 22, 2012


There are two tabs, one on each side that will release the drawer to slidr forward. I have enclosed a photo of the square tab on one side. press both sides in and pull the drawer toward you . There shouls be a wire bale on the rear that hods the water lines. If these are interfering with the seal that will be the cause of your leak.7_3_2012_2_56_28_am.jpg

Fisher and... | Answered on Jul 03, 2012


I wasn't able to find an exact match to your reported model (DD603I?), but all of the DD60xx models appear to have the same drawer removal process:

2_23_2012_6_18_56_am.jpgI actually took this from the installation guide for the KitchenAid dishdrawer (also made by F&P), since it had the clearest images.

Fisher and... | Answered on Feb 23, 2012


This picture of the rotor shows two of the three clips that hold it in the washer tub. They protrude from the smaller tan disc sitting just above the red magnet subassembly. Normally, you would unlatch and remove the filter plate, then unlatch the rotor assembly by turning the larger tan disc (with the three arrow tabs) counterclockwise until it stops. Since the top of your assembly is broken off, you'll need to turn the smaller disc counterclockwise about 1/8 turn, so the clips can slide up through their slots. The magnets in the rotor also hold it down somewhat, but it should be possible to slide the rotor out by hand.

The rotors in my double dishdrawer were deteriorated to the point that the plastic around the magnets was crumbling. Note that although the plastic around the magnets is red in this picture, all 4 rotors I have actually seen have blue plastic encasing the magnets, similar to that used for the impeller. I suppose it is possible that your magnets have come completely loose, and are jamming the rotor in place, or that some other foreign matter is caught in the drain impeller at the bottom of the rotor. But there isn't normally any physical connection at the bottom of the rotor- the lower impeller spins freely to pump water out the drain.
2_23_2012_5_42_29_am.jpg

Fisher and... | Answered on Feb 23, 2012


on the hinge slide there is a micro switch the draw needs to be removed to locate it.

Fisher and... | Answered on Feb 18, 2012


thats tub home sensor switch, mounts to rear right of cabinet and senses drawer closing along with little black box with red switch should also have a little metal actuator( this is what usually breaks off switch), each drawer uses their own. unistall from cabinet and theres an access panel strictly for replacing theses switches

Fisher and... | Answered on Nov 30, 2011


I'm not really sure. With the double drawer configuration, I know the top drawer is larger than the bottom drawer. If I had to take a guess, I would say the single drawer might fit in the top of the double drawer.

Fisher and... | Answered on Nov 30, 2011


Hi - F2 error code indicates a failure of the rotor/motor or the sensors, the following notes should give you guys something to check and see which of these has failed..

Error Code - F2


Which LED - Delicate LED


Reasons - The motor has not been sensed rotating


Likely Causes

_ Foreign object has jammed the rotor

_ The rotor has failed

_ The hall sensor has failed

_ The electronic controller has failed

Fisher and... | Answered on Aug 25, 2011


Hi


This error on your fisher & paykel means an overfill condition. One of the most common causes for an overfill fault is that the dishwasher cannot pump out the dirty water due to a plugged drain hose. Check the drain hose if it is clogged. Now remove the bottom drawer from the unit to inspect the flood switch. Remove the wire harness cover on the underside of the drawer. With the bottom cover off, unclip the wire harness, fill hose, and drain hose. Then unclip the linkage at the back of the drawer and lift the drawer off the slider arms. Now' you'll be able to look at the flood switch. Note the positions of the wires on the flood switch and remove them. Then unclip the switch housing from the base panel. The switch housing contains one switch for each drawer. The switches are wired normally closed (NC) and each switch has three spade connections, so it's important to note where the wires went. Now clean the contacts and let it dry. Hope this helps... Please post back if you need more information.
Daniel

Fisher and... | Answered on Jun 23, 2011


F2 - Rotor may be jammed - blocked, the rotor has failed, hall sensor cold be faulty, faulty stator windings or there is a faulty electronic controller, the other could be the mains power filter.

So as you can see there a number of components that possibly be the cause, will rerquire the services of a serviceman familiar with F & P disdrawers..

Fisher and... | Answered on Jun 21, 2011


Hi,


Thank you for contacting fixya.com.


The drawer may not be seated in the track correctly. Make sure that the retaining tabs on either side of the drawer at the lower front are engaged properly. Unfasten the tabs and re-engage them a couple of times to check. Also check whether the hoses are obstructing behind the drawer or the linkage support is broken.If it's broken it will prevent the drawer to open properly.Also you can reboot the unit by unplugging it and again plugging in to reset the machine and see the drawer is closing without any hindrances or not.


Please get back to us if you have further query else please accept the suggestion.


Fisher and... | Answered on Jun 13, 2011


Are you sure it shows UI or U1 . To help you check this Fisher&Paykel service manual and find among error codes. The manual is here!

Fisher and... | Answered on Jun 03, 2011


Hi,

Is it F1 or E1?

F1 code - F-1 means flood condition, F1 means that the unit is detecting water underneath the bottom drawer. pull the bottom drawer out and put in on the plastic tabs on the side near the bottom just behind the front panel, pull the drawer out far enough to slide a towel behind the drawer,you need to soak up all the water you can , then you may need to use a hair dryer to dry the sensor in the left back corner, when the sensor detects that there is no more moister in the pan the F-1 will go away, sometimes the cause for this is stacking the dishes to high and the lid doesn't shut down tight and seal the drawer.

If the problem is not resolved by the above procedure, you might be looking at replacing mains filter board which would cost around $50. However, at this point i would rather advise you to call a tech to make sure what exactly the problem is.

E1 is another issue with few models and more likely the concern is faulty controller. The buttons are usually unresponsive in this case.Tech are recommended in this error.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Fisher and... | Answered on May 20, 2011


Hello,

This repair is simple. Open the door and on the lower front corner you will see a tab depress and push the rack forward.

Fisher and... | Answered on Apr 03, 2011


The f1 fault is cased by a leak on the dishwasher.
It is activated when water gets to a dangerous level in the base of the appliance near to the PCB.

The main reason this happens is putting cups on the drop down shelves and when the lid comes down to seal the drawer it can't and leaks. If you look at the drawer when open there is a lip around it, if anything is proud of this lip the lid will not shut properly.

To rectify this problem you will have to disconnect the power and remove the bottom drawer and the dry up all the water in the base. If you leave the appliance long enough it will dry out by itself.

Once you have done this and the problem still comes back you will need and engineer as there is a problem with the lid motors or the seal’s.

Fisher and... | Answered on Mar 26, 2011


Take out the two plastic pins one on each side with a nose plyer.

Slowly pull the front cover out without dropping the top panel.

Hope this helps. It would be useful to mention why you are looking at taking the front of tub out.

Fisher and... | Answered on Mar 13, 2011


Hi,



I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and installed them in minutes...now the thing works like new... However I have also found that if the heating element goes bad then that also can mess things up bad... So I would buy new spray arms, and also check out the heating element to make sure it is working... Here is a tip that will help you with the online buying...


Dishwasher
Spray Arms not Spinning

How to Buy
Appliance Parts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The
Heating Element not Working

Dishwasher Maintenance



Dishwasher Residue and Film on Dishes



heatman101

Asker's Testimonial "explanation very clear. will give it a go and see how simple it was. thanks Ronnie " - ronnieshomes
/.././

Fisher and... | Answered on Feb 27, 2011


Fisher Paykel dishwasher repair video, this video will walk you through repairing your dishwasher.
http://www.appliancerepairlesson.com

Fisher and... | Answered on Feb 26, 2011


Hi

Error F1 on your fisher & paykel means an overfill condition. One of the most common causes for an overfill fault is that the dishwasher cannot pump out the dirty water due to a plugged drain hose. Check the drain hose if it is clogged. Now remove the bottom drawer from the unit to inspect the flood switch. Remove the wire harness cover on the underside of the drawer. With the bottom cover off, unclip the wire harness, fill hose, and drain hose. Then unclip the linkage at the back of the drawer and lift the drawer off the slider arms. Now' you'll be able to look at the flood switch. Note the positions of the wires on the flood switch and remove them. Then unclip the switch housing from the base panel. The switch housing contains one switch for each drawer. The switches are wired normally closed (NC) and each switch has three spade connections, so it's important to note where the wires went. Now clean the contacts and let it dry. Hope this helps... Please post back if you need more information.

Fisher and... | Answered on Jan 31, 2011


Greetings,
There are a few things that could keep it open..check to see if your lid is closing.. there are hoses and such that can cause this..Try and unplug it or turn off breaker and let sit 5 minutes..see if it works...Again, there could be problems with the lid closers..

Fisher and... | Answered on Jan 27, 2011

Not finding what you are looking for?
Fisher and Paykel 24 in. DD603H W Built-in Dishwasher Logo

246 questions posted

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Dishwashers Experts

Mark Davis

Level 1 Expert

18 Answers

Bruce Denton

Level 2 Expert

273 Answers

Paul Bade

Level 3 Expert

1662 Answers

Are you a Fisher and Paykel Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Fisher and Paykel Dishwashers

  • Fisher and Paykel Dishwashers

Most Popular Question

disable bottom drawer fisher paykel

  • Dishwashers
Loading...