20 Most Recent Mitsubishi WD62628 62" Projection HDTV - Page 3 Questions & Answers


usinng the av cable (1 yellow, 1 red, 1 white), on the back of the set
plug them into input one. input one is actually the third set of jacks down on the terminal board. the first is audio out. the second is monitor out (it has video) and the third is input one.if input one does not show on your device menu the you will have to add it with the netcommand menu.

Mitsubishi... | Answered on Jan 07, 2009


on front of tv next to lamp lite need to reset with small pin or paperclip

Mitsubishi... | Answered on Dec 28, 2008


Yes you can replace just the screen. Various retailers sell them online. Do a search online, and if you need instruction on how to replace the screen, you can get a manual usually at this link. Hope this helps. http://www.smshop.org/

Mitsubishi... | Answered on Dec 25, 2008


Mitsubishi TV troubleshooting
Here's something that might also be useful. After you turn on the set, and get the regular red blinky lights, hold down the Device and Menu buttons together for about 5 seconds.
The Power light will start to flash in a two digit sequence.
For example, 3 flashes, then 7 flashes = 37.

Here are the error codes, and the corresponding problem:
12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filter cover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cable between FMT and Engine disconnected

Mitsubishi... | Answered on Jun 25, 2008


I don't know your set in particular, therefore I will be generic.

On some projection sets, there is an hours counter that is manualy resetable. Make sure that it is reset. If you can have a readout of the amount of hours used on the lamp this will tell you if this needs to be reset.

Normaly, when the set reacts as per your description, there is a cooling problem, or a fault in the power supply.

Also with your model of set, check to see if there are any safety switches that work with the cover or door for the lamp access. With the safety switch option, if the uPC thinks that the lamp is not properly enclosed or installed it will not allow for proper startup.


Jerry G.

Mitsubishi... | Answered on Apr 13, 2008


if you have experience in electronic repairing why not! but if not! dont do that! coz that is sensitve intalling and they have high voltage to harm you! get authorised tecnician for best result. havce a good day!!!

Mitsubishi... | Answered on Mar 10, 2008


Intermittent problems are the most difficult to find because they don't show up long enough to trace them down. Today the digital sets are all cpu controlled and a glitch from any board can lock up the set. The problem can even be software related, such as settings or firmware updates. Unfortunately we as technicians do not have a history of symptom/cause on the newer digital sets. Your best bet is to e-mail Mitsubishi with the symptom as described above, such as the blinks, E2P, signal source etc ... and ask them what they think. techservice@mdea.com good luck

Mitsubishi... | Answered on Jan 31, 2008


what lines are you seeing?

Mitsubishi... | Answered on Jan 21, 2008


sounds like power supply caps or caps in the dm board
http://www.auctioncreations.com/wd62525a.JPG

The DM board is the one with the digital connectors on the back panel. If you already have it appart, you may as well check the caps on all of the boards. The caps that go bad are typically Jamicon brand caps in 1000 uF and 330 uF values. There are also a couple of 3300 uF caps in the PS that cause problems.


Mitsubishi... | Answered on Jan 08, 2008


http://www.auctioncreations.com/wd62525a.JPG

The DM board is the one with the digital connectors on the back panel. If you already have it appart, you may as well check the caps on all of the boards. The caps that go bad are typically Jamicon brand caps in 1000 uF and 330 uF values. There are also a couple of 3300 uF caps in the PS that cause problems.

Mitsubishi... | Answered on Jan 08, 2008


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
https://homenol.blogspot.com/
https://electronicshelponline.blogspot.com/
If blinks continue without any pause, or the LED light stationery; the main board is faulty.
Search the site by type in the "brand name" to your device; [Exclude the model number], in the "Search box at the top right of the display window of the Homepage" to get gathered related posts. See the site by a desktop. Mobile view has no search box. If you are viewing it by your mobile, see it in webview/

Mitsubishi WD... | Answered on Jul 10, 2018


Basing the replacement of the board on the clicking sound of a relay trying to close is not a safe bet. The first thing you need to do is check the bulb. Then there is a ballast board and then the Power supply board. Parts might be hard to find. Use the website I listed to see what part numbers are then google it or look on eba or amazon for those parts. Mitsubishi WD 60C8 TV Parts

Mitsubishi WD... | Answered on Jan 18, 2018


Most likely a fuse blew when the lamp blew, there is internal fuses on the power supply board on these mitsubishi's, if the fuse is ok though then most likely another component somewhere failed.

Mitsubishi WD... | Answered on Jan 02, 2018

Not finding what you are looking for?
Mitsubishi WD62628 62" Projection HDTV Logo

62 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1257 Answers

The Knight
The Knight

Level 3 Expert

76171 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

WD Mitsubishi

  • WD Mitsubishi

Most Popular Question

black lines come go not stay all time

  • Televison & Video
Loading...