20 Most Recent Mitsubishi WD62628 62" Projection HDTV - Page 6 Questions & Answers


Not uncommon for the fan to stay on for a few minutes after the set is turned off. It is designed that way and then supposed to shut down after a few minutes. If it does not then that circuit is defective.

U can always throw a switch in series with the fan and shut fan off after you turn set off. Or if you wanna be fancy you can rig up a relay setup that will turn the fan on/off as you do with the tv.

Mitsubishi WD... | Answered on Nov 13, 2015


Hi Kenny
Being a projection device... Which most TV's aren't ...
You need to break the fault down into the Projection Section or the TV Section.
Or Power Supply Section
Projector bulb blown, overheating etc.
Power supply sensing overload or fault then automatically shutting down.
TV Section may be OK
small internal LCD screen is projected by lens.
Check internals.
Happy Troubleshooting

Mitsubishi WD... | Answered on Nov 03, 2015


Cooling fan gone and cutting out on overheat? These projections televisions are so old tech :>)

Mitsubishi WD... | Answered on Oct 14, 2015


not the lamp. Its a known issue with the power supply. Bad capacitors usually. this requires a servicer to repair it.

Mitsubishi WD... | Answered on Oct 02, 2015


press the power button onthe front. if nothing happens please post back with what indicator lights are flashing and how many times they flash. Be sure the lamp door is secure or it will not turn on.

Mitsubishi WD... | Answered on Oct 02, 2015


The Ballast plug melted due to age of the TV. as the plastic gets old it gets brittle and can crack with barely any force. The pins then do not seat and the arc that should be in the lamp takes place in the connector. I have seen this so many times. fortunately it is very easy to replace the connector is you know how to use wire crimps and can source an old female plug. eBay is a good source. you can buy a used ballast from any model that has the same connector. Then cut off the new plug and splice it onto your old wires with but-crimps and shrink tubing.

Mitsubishi WD... | Answered on Oct 02, 2015


You are going to ruin the optics using a Xenon lamp. The ballast in the TV talks back via UART to the CPU. By removing the ballast the TV cannot talk to it and run itself properly. Also using a xenon lamp will give terrible color reproduction as its not putting out nearly enough lumens in the right spectrum. It will also bombard the color wheel and DLP chip with UV light and ruin those as well.

Mitsubishi WD... | Answered on Sep 15, 2015


in repair shop

Mitsubishi WD... | Answered on Jul 11, 2015


Fault to the main power supply regulator board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
http://electronicshelponline.blogspot.com/

Mitsubishi WD... | Answered on Jun 14, 2015


Probably a bad lamp. what is the model?

Mitsubishi WD... | Answered on Jun 03, 2015

Not finding what you are looking for?
Mitsubishi WD62628 62" Projection HDTV Logo

62 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1257 Answers

The Knight
The Knight

Level 3 Expert

76171 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

WD Mitsubishi

  • WD Mitsubishi

Most Popular Question

black lines come go not stay all time

  • Televison & Video
Loading...