20 Most Recent Mitsubishi WD62628 62" Projection HDTV - Page 9 Questions & Answers


there may be display problem

Mitsubishi WD... | Answered on Sep 03, 2014


It sounds like you need to re-adjust your convergence. The purpose of adjusting your convergence is to align your red, green, and blue colors. Moving your TV often causes this problem. I hope you get it going.

Mitsubishi WD... | Answered on Sep 03, 2014


If the lamp is new and good to go then you may have to reset the lamp replacement counter in your setting menu. When that is set back to zero you wont have a problem until it is time for a new lamp again.

Mitsubishi WD... | Answered on Aug 23, 2014


Basically, all you need is:
1- Power-up the camera.
2- Select video input 1 or 2 on your TV.
3- Run a cable from the camera to the TV
4- Connect the cable coming from the camera to video input 1 or 2 on your TV.

Please note:
The cable you run from the camera to the TV has 2 Ends.
One End connects to the camera (BNC plug) the other End connects to the TV (RCA yellow plug)

I hope this helps. If not, provide the model# for the TV and camera, and if I come across your post I will be Happy to contribute.

Best of luck
www.aaatvservice.com

Mitsubishi WD... | Answered on Aug 16, 2014


Might be tuned to the wrong output. The big tv has more than one input and is select able. Is there a blue ray selection for TV or input for that device.

Mitsubishi WD... | Answered on Aug 09, 2014


It is helpful to have the sequence of the blinking red light. This may help:

MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927

Page 43

3. Error Code Operational Check

Note: The TV must be in "Shut Down" and not have been switched Off, to perform the Error Code Operational

Check. When the TV is switched Off, the code automatically resets to "12" No Error.



Pressing the front panel "DEVICE" and "MENU" buttons at the same time, and holding for 5 seconds,

activates the Error Code Mode. The LED flashes denoting a two digit Error Code, or indicating no problem

has occured since the last Initalization.



Note: The front panel buttons must be used, NOT those on the Remote Control.



• The number of flashes indicates the value of the MSD (tens digit) of the Error Code.

• The flashing then pauses for approximately 1/2 second.

• The LED then flashes indicating the value of the LSD (ones digit) of the Error Code.

• The Error Code is repeated a total of 5 times.



Example: If the Error Code is "23", the LED will flash two times, pause, and then flash three times.



4. Error Codes

The Error Code designations indicating malfunction, or no malfunction, are listed below:

POWER

LED

STATUS

LED

LAMP

LED

Power

Status Condition

Off Yellow Off Low

Power Excess heat. Check Lamp Filter

Off or On Off Yellow No

change

120w usage time over 7000 Hrs.

150W usage time over 3500 Hrs.

Off Off Blinks

Yellow

Low

Power Lamp Cover open

Off Blinks

Yellow Off " Filter Cover Open

Off Off Red Stby Lamp did not turn On

Off Blinks

Red Off Low

Power Fan Stopped

Off Red Off " Circuit failure (short or DVI

connector unplugged)

Abnormal LED Indications

Error Codes "DEVICE" & "MENU"



Error Codes Description



12 No error detected

22 Recovery from Reset

32 Lamp cover is Open

34 Lamp abnormality

35 DM Fan failed (Chassis Fan)

36 Exhaust or Lamp Ballast Fan failed

37 DMD Engine Fan failed

38 Lamp temperature abnormally high. Remove Lamp to check filter.

39 DMD temperature abnormally high

41 Short is detected (Standby Power Supplies)

42 Lamp Fan failed

44 DVI cable between Format and Engine disconnected

46 DMD Temp. Sensor not detected (check DT connector))

47 DM Temperature too high

48 Engine power supply short detected

51 Speaker Drive circuit short detected

52 HDD excess temperature (V30+ & V31 only)

55 HDD Fan Stopped (V30+ & V31 onlyt)

Mitsubishi WD... | Answered on Jul 25, 2014


Try a new lamp. You will need the model# to locate the proper part# for your unit.

Mitsubishi WD... | Answered on Jul 24, 2014


Hello:

From the sound of your description of your problem you likely have a defective lamp. Feel free to give us a call at 866-764-5822 and we would be happy to help you troubleshoot the problem over the telephone.

Best Regards
Dan
DLP Lamps Projector Lamps Specialty Lighting

Mitsubishi WD... | Answered on Jul 03, 2014


Condensor? or just the projection lens.
Condensor is just a lens like pice of glass used you distribute the light of the lamp evenly.

Mitsubishi WD... | Answered on Jun 12, 2014


When you replaced the lamp did you reinstall the cover correctly?
There is a safety switch incorporated in the cover .

Mitsubishi WD... | Answered on Jun 01, 2014

Not finding what you are looking for?
Mitsubishi WD62628 62" Projection HDTV Logo

62 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1257 Answers

The Knight
The Knight

Level 3 Expert

76237 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

WD Mitsubishi

  • WD Mitsubishi

Most Popular Question

black lines come go not stay all time

  • Televison & Video
Loading...