Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher - Answered Questions & Fixed issues


Hello Mileshjr,

I don't disagree... Nice looking unit...

What you have to do is assess the LEAK(s)...
and do a cost/benefit analysis...

If indeed the parts are available (they seem to be)

http://www.appliancepartspros.com/motor-pump-parts-for-frigidaire-fdb1050rec0.html

Then all you have to do is find the cause of the
LEAKS and repair them...

Mine turned to be rusted body panels...
(not much you can do there... Unless you
find a complete DONOR... Not unlike restoring cars...

(the labor of love)...

Check out other part houses...

Repair-clinic
Appliance Parts Lawn Mower Parts Heating Cooling Parts 365 day returns

Part-Select
PartSelect Appliance Parts and Repair Help

... and don't forget to check eBay.

I will confess the new PRO Series "QUIET" models
are VERY quiet... and sooo... pretty I had to REMODEL
the ENTIRE KITCHEN... (no savings there).

Hope this saves $$$$


Carnac the Magnificent

Frigidaire 24... | Answered on Mar 15, 2019 | 109 views


If the cycle does not run I say the timer is in need of repair/replacement. Go to site for parts Search Over 2 1 Million Appliance Parts

Frigidaire 24... | Answered on Aug 29, 2017 | 80 views


nothing specific until you get a technician to properly diagnose the fault

Frigidaire 24... | Answered on Aug 19, 2017 | 380 views


The intake light blinking error can be caused by several different problems and may take some pains taking effort to figure it out. There is some helpful information about Intake/Drain light flashing. http://www.techanswerslive.com/appliances/miele-icognito-dishwasher-service-mode-error-codes/12

Frigidaire 24... | Answered on Nov 16, 2015 | 821 views


That gasket is supposed to look like that. Use less soap and/or replace that gasket. It is very easy to do but pay attention to how the old on is placed. There is a small notch that has to be placed right.

Frigidaire 24... | Answered on Feb 08, 2015 | 154 views


Good Morning Friend,

I understand your Frigidaire dishwasher, model# FBD1050REC, will start on delay start but not just by pressing the start button. Please try resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 20-30 minutes. Restore power and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.

-Best Regards-
WP

Frigidaire 24... | Answered on Jan 24, 2015 | 423 views


Hello friend, thanks for your inquiry!

On your Frigidaire dishwasher "i30" stands for aqua control. You should perform a reset on your dishwasher and that could clear any false error codes. To reset your dishwasher you can flip the household circuit breaker off for ten minutes. If that does not work you could be experiencing an issue with your water inlet valve or control panel. I hope this information has been helpful. -Matt

Frigidaire 24... | Answered on Oct 16, 2014 | 4,866 views


Good Afternoon Friend,

I understand your Frigidaire dishwasher, model# FDB1050REC, is not drying your dishes. I also see you want to know which part needs to be replaced. Typically, this is not a do it yourself repair, as there are no step by step instruction manuals. I suggest contacting your local authorized technician for further assistance. They will be able to diagnose and determine what exactly is causing your appliance to not dry the dishes. Hope this is helpful.

-Best Regards-
WP

Frigidaire 24... | Answered on Jul 08, 2014 | 190 views


Good Morning Friend,

I understand you are replacing the soap dispenser in your Frigidaire dishwasher, model# FDB1050REC, and want to know how to access the screws to remove front panel of the door. Typically, this is not a do it yourself repair, as there are no step by step instruction manuals for this repair. I suggest contacting your local authorized technician for further assistance. I hope this is helpful.

-Best Regards-
WP

Frigidaire 24... | Answered on Jun 23, 2014 | 100 views


Good Afternoon Friend,

I understand that your Frigidaire dishwasher, model# FDBB4365FC0, will not drain. I also see that you do not have a manual. Try these troubleshooting tips below.

    1)If your appliance is hooked up to a garbage disposal, make sure the disposal is empty.

    2)Make sure the knockout plug has been removed from inside the garbage disposal.

    3)Check to see if the drain hose is kinked.

    4)Make sure the cycle is complete and not in pause.

    I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your dishwasher status has changed successfully. Hope this is helpful.

    -Best Regards-
    WP

Frigidaire 24... | Answered on Jun 12, 2014 | 75 views


Good Morning Friend,

I understand that your Frigidaire dishwasher, model# FDB4315LFC2, starts and then stops, and flashes a "PF" code when it stops. The "PF" code is stating that there has been a power failure. There could be a possibility that your dishwasher is losing power mid-cycle. I suggest checking your home's circuit breaker, the wiring to your dishwasher, and if you have a cut-off switch, checking that as well. I also suggest resetting your appliance, by shutting the power off at your home's circuit breaker, for 20-30 minutes. Restore power and start any cycle. If further troubleshooting is needed, I ask that you please let me know the error codes displayed on your appliance. Hope this is helpful.

-Best Regards-
WP

Frigidaire 24... | Answered on Jun 12, 2014 | 386 views


Good Afternoon Friend ,

I understand that you are looking for the manual to your Frigidaire dishwasher, model# FDB510. Hope this attachment helps.

-Best Regards-
WP

Frigidaire Manual Search Results

Frigidaire 24... | Answered on Jun 02, 2014 | 85 views


Hello Gary, I am happy to assist you! I see that your Frigidaire dishwasher is displaying error code EO; however, is it possible that the code is missing a number or character(s)? Typically error code "E0" is follow by another number. In the meantime, you can reset your dishwasher. This can be done by either unplugging it or flipping the household circuit breaker off. It is important to wait approximately ten minutes and then turn on your appliance. If resetting the power does not correct the issue, could you please advise me of the new error code or if it continues to display "EO"? With this information I can better address the issue at hand. Thank you! - Z

Frigidaire 24... | Answered on May 22, 2014 | 320 views


It is likely that sufficient water is not coming from the top arm. These dishwashers oscillate the water flow between top and bottoms sprays alternatively. This ensures water is pumped with adequate force. It is possible this mechanism is not working correctly. The device called check ball item 58 in this diagram actually does this function. The ball might be out of shape or not sitting properly causing incorrect wash water movement.

http://www.searspartsdirect.com/partsdirect/part-model/Frigidaire-Parts/Dishwasher-Parts/Model-FDB1050REC0/1428/0130000/R0505129/00004?blt=06&prst=&shdMod=

Frigidaire 24... | Answered on Jun 05, 2014 | 204 views


Good Morning Friend,

I see that you are receiving grit and a white film on your glasses, in your Frigidaire dishwasher, model# FDB1050REC. Here are some common solutions that you can begin with.

-Check your water hardness. Hard water can cause lime deposit buildup on the interior of the dishwasher. Dishes and glasses may also get spots and film for a number of reasons. To remove buildup, spots and film, clean using the following instructions:
1. Load clean dishes and glasses in a normal manner. Do not load any metal utensils or silverware.
2. Do not add detergent.
3. Select the NORMAL WASH cycle. Close and latch door. Press START/CANCEL pad.
4. Allow your dishwasher to run until it starts the second water fill (approximately 10 minutes).
5. Unlatch and open the door, and pour 2 cups of white vinegar into the bottom of dishwasher.
6. Close and latch the door and allow the cycle to finish.
For extremely hard water, it may be necessary to install a water softener.

-Your water temperature may be low. Avoid extremely low or high temperatures.

-Avoid overloading and improper loading.

-Make sure you are using fresh detergent. Old detergent is ineffective.

-Make sure your rinse aid dispenser is filled.

-Check to see that the proper amount of detergent is being used for cycle selected.

-Your home water pressure may be too low-it should be 20 to 120 pounds per square inch (psi).

If none of these suggestions helps, I would suggest contacting either the manufacturer or a local authorized technician. Hope this helps.

-Best Regards-
WP

Frigidaire 24... | Answered on Apr 09, 2014 | 134 views


Hello Friend,

I see that you are wondering how to clean the filter on your Frigidaire dishwasher, model# FDB1050REC. The inside of your dishwasher is self-cleaning with normal use. If needed, clean around the tub gasket area with a damp cloth.

The filter is self-cleaning. A glass trap located in the center of the filter is designed to collect pieces of broken glass, straws, bones, and pits. To remove this glass trap, grasp the handle, lift out, empty it and replace it. Hope this helps.

-Best Regards-
WP

Frigidaire 24... | Answered on Apr 08, 2014 | 341 views


Good Afternoon Friend,

I see that you have standing water in your Frigidaire dishwasher, model# FDB105RES. I would suggest trying the troubleshooting tips below:

• If your appliance is hooked up to a food waste disposer, make sure the disposer is empty.

• Check to see if the knockout plug has been removed from inside the food waste disposer inlet.

• Check to see if the drain hose is kinked.

• Make sure the cycle is complete and not in a pause mode.

If you are still having trouble with your dishwasher not draining, I recommend contacting either the manufacturer or a local authorized technician. Hope this helps.

-Best Regards-
WP

Frigidaire 24... | Answered on Apr 08, 2014 | 275 views


Good Morning Edward,

I see that you are having trouble with running your Frigidaire dishwasher, model# FDB1050REC, due to the "Clean" light being stuck on. I also see that regardless of you trying to reset the appliance, it might run through one cycle and then you're back to showing the "clean" light, and not being able to clear that light. It sounds to me like your control panel is having issues and might need to be replaced. I do suggest contacting a local authorized technician to diagnose the appliance, this way you're not just purchasing random parts.

-Best Regards-
WP

Frigidaire 24... | Answered on Apr 04, 2014 | 119 views


Hi Mark, this is AP and I'm happy to assist you!

I understand you are having trouble with your dishwasher not draining and making odd noises. I would suggest checking the drain hose to ensure it has not become twisted or kinked. Even if the hose is not kinked make sure it has not fallen behind the dishwasher either as this can prevent draining. Additionally, you could check the filter at the bottom of the tub to make sure no debris has clogged the filter or disposal. Other than that the drain pump could be the culprit. If so, I would recommend a local authorized technician to come out and properly diagnose the dishwasher. I hope this information helps.

Frigidaire 24... | Answered on Mar 17, 2014 | 75 views

Not finding what you are looking for?
Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher Logo

569 questions posted

Ask a Question

Usually answered in minutes!

Top Frigidaire Dishwashers Experts

Mike

Level 3 Expert

4369 Answers

Vitally Alcher

Level 3 Expert

1645 Answers

Brad Brown

Level 3 Expert

18165 Answers

Are you a Frigidaire Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...