Top 20 SMC EZ Connect g SMCWEBT-G Questions & Answers


I'm unsure of the exact part number here but using the model number I checked the manual. This looks like it's just an access point which extends a current network you have. If you only have your laptop, this device and your internet modem it may not give you the wireless connectivity you're looking for. On a normal setup you would plug your modem into a router, plug your laptop into the router and set it up with all your DSL/Cable connection information as well as wireless on/off. You can then unplug from the router and continue life. with this one it's only connecting to an existing setup (another router or another wireless network) and extending it.
If you are looking for a solution to give you a router that connects to your modem and gives you wireless or adding multiple devices on a single connection I would recommend returning this and getting an all-in-one router such as this: http://homestore.cisco.com/en-us/Routers/Linksys-E1000-Wirelessn-router_stcVVproductId97826160VVcatId551966VVviewprod.htm?icid=linksys-specs-e1000-learnmore-btn&src2=linksys-specs-e1000-learnmore-btn

SMC EZ Connect g... | 324 views | 1 helpful votes


Make sure there is not same ip addreses in router and computer.
Enable DHCP server in router configuration page.
For that connect your router t ocomputer with ethernet cable.
Then you can access it with following link.
http://192.168.1.1
or
http://192.168.0.1
type user as "admin" and password as "admin" or blank or "password"
then you can see configuration page of router.
Then go to advanced option and find DHCP enable DHCP.
Then save settings and restart router.
If still not works then RESET router.
For that RESET button is in back panel of router press it for 10 seconds.
Then configura your router with above link.
Let me know if you need further assistance.
Thanks.

SMC EZ Connect g... | 71 views | 0 helpful votes


It may because you have a mac filter on. If so you can correct this by connecting to the router then in a Internet explorer type 192.168.1.1 and you should have a configure screen available then either disable the mac filter or enter the other mac adresses. Good Luck

SMC EZ Connect g... | 467 views | 0 helpful votes


you make a device into ap mode you can get it

SMC EZ Connect g... | 3,918 views | 0 helpful votes


update the firmware of the all device

SMC EZ Connect g... | 714 views | 0 helpful votes


There suppose to be a reset button on it mainly on the back of it

SMC Computers &... | 70 views | 0 helpful votes


different USB port. There are usually 3 or 4 of them. If you can, format the USB drive (if you have nothing on it or already have copies of what is on it). It will take 10 seconds, but will wipe all data. It should be recognized then.

SMC Computers &... | 23 views | 0 helpful votes


look for a windows xp driver file on the included program compact disc that may need to be installed before you use the included program.

SMC Computers &... | 60 views | 0 helpful votes


The question doesn't make sense but I'll assume you mean,
How fast is it.
It's set by the IEEE standards.
IEEE802.11
Look for eg. 802.11n
The letter at the end will give you an idea of it's speed.
N is current standard
AC is the most up to date
a & b are old standards

See http://en.wikipedia.org/wiki/IEEE_802.11

Cheers
Trevor

SMC Computers &... | 61 views | 0 helpful votes


Ask a question.

SMC Computers &... | 93 views | 0 helpful votes


Why is this posted in Networking? Solaris 4x4 650 cc quad bike. Tune up specs are required has nothing to do with Computers/NETWORKING

If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_d799f810c7212a78

SMC Computers &... | 134 views | 0 helpful votes


JRod3,

Your new Laptop is capable of Wireless N theoretical transfer rate of 300 mbps with two antennas. Your router is wireless G at max. theoretical transfer rate of 54 mbps. I would recommend replacing your router with one that has wireless N. I use a Motorola Surfboard SBG6580. With some routers you can go into your settings and disable the firewall which will help with the speed. Firewalls can sometimes be redundant if you have a firewall in your operating system (windows) anyway. Before you run out and get a new router I would hardwire your laptop to the router (cat5E cable) you have now just to make sure you don't have a bottleneck somewhere else. Then do a speed test using your Vuze program. You may need to Port Forward your router, not always necessary..... you can get lots of info at portforward.com on your specific router. Depending on your speed that you are paying for from Time Warner you want to make sure you have the right router as well. Here is a list Buy Your Modem Time Warner Cable . If you reach your desired speeds hardwired to your laptop then I would get the new Wireless N router. Good Luck.

SMC Computers &... | 353 views | 0 helpful votes


Hi,efault

U need to isolate the problem first.
Check if the wireless drops on all devices or only on one particular device.
If it occurs on only one particular device,the problem is with the wireless adapter of that advice..

If it happens on all the devices then the problem is with wireless router

For that
Check for the wireless interference . Avoid having cordless phone base near the router.
Also try changing the wireless channel of the router To 1,6,11

U can do this by logging on to the router set up page of your router

To Find the address of your router,type ipconfig /all in the command prompt.Look for the Default gateway address and type it in the address bar.U will find your Router set up page..and u can change the wireless channel there

SMC Computers &... | 56 views | 0 helpful votes


Communication restraints are relative to authorizations necessitated when setting passwords. Review the detailed data provided by the Modem/Router/Extender supplied to you when you obtained the hardware. Full instructions were given to you at that time on the procedures to set and reset communication authorization and codes. If you cannot follow the instructions, the OEM (equipment mfg.) will be happy to walk you through the process of completing and new link to your devices.

SMC Computers &... | 41 views | 0 helpful votes


Easy put all settings on dhcp and reboot system

SMC Computers &... | 50 views | 0 helpful votes


Printed on the label on the bottom of the unit. If that doesn't work, do a factory reset with a paper clip in the reset hole.

SMC Computers &... | 44 views | 0 helpful votes


You can use TELNET from the command prompt in Windows, but you need the name / IP address and login credentials.

SMC Computers &... | 149 views | 0 helpful votes

Not finding what you are looking for?
SMC EZ Connect g SMCWEBT-G Logo

Popular Tags

8 questions posted

Ask a Question

Usually answered in minutes!

Top SMC Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Jeffrey Groves
Jeffrey Groves

Level 3 Expert

573 Answers

Cindy Wells

Level 3 Expert

6069 Answers

Are you a SMC Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

SMC Computers & Internet

  • SMC Computers & Internet

Most Popular Question

bought smc wireless router tries

  • Computers & Internet
Loading...