20 Most Recent NetGear WG111T 108 Mbps 802.11g Wireless USB 2.0 Network Adapter (NETWNGWG111T) - Page 7 Questions & Answers


Keith, try another channel. Often times default channel on the router interferes with other devices in the environment, even up to 1/2 mile away. Channel change almost always solves it.

NetGear... | Answered on Sep 21, 2016


username:-admin
password:-password

if its not working reset the router user them again


skype id :- johnwalker800969@gmail.com

NetGear... | Answered on Sep 13, 2016


https://www.netgear.com/support/product/DGND3700v2.aspx?cid=wmt_netgear_organic

NetGear... | Answered on Sep 10, 2016


Here's and excerpt from the Netgear WNR2000 user manual explaining that this is normal behavior for Netgear routers that support WPS..:
  • Keep Existing Wireless Settings. This check box is automatically selected after WPS is enabled to prevent unwanted settings changes, and is also selected if you have already specified wireless security settings or your SSID without using WPS. When this check box is not selected, adding a new wireless client using the push button or the Add WPS Client screen (see "Push Button Configuration" on page 2-14) changes the router's SSID and security passphrase. You might need to clear it if you are using certain registrars, such as for a Windows Vista PC, to configure the router through WPS.
Even if your router is not a WNR2000, it is likely that the configuration interface pretty much the same so you might be helped by looking at Chapter 2 page 17 in the WNR2000 manual here..:
Or else, go to Netgear support (NETGEAR Support Welcome), select Wi-Fi routers and download/display the user manual pdf and search it for "disable router's pin" or "keep existing wireless settings" and verify/change the setting so the router doesn't make changes when you use the WPS button.

NetGear... | Answered on Jun 10, 2016


I would go to Netgear's website and follow the instructions.
The pin is normally on the label with the serial number.

NetGear... | Answered on May 02, 2016


Do you wish to connect via Ethernet or wireless? if wireless you need to know the wireless key, or you can connect via the WPS function.

NetGear... | Answered on Apr 20, 2016


What kind of router?Sorry I do not know how to set that kind up I can give you a video on how to set up a router that might give you an idea on how do you want me to do that?Connect the router's WAN port to your Internetsource, such as a DSL or cable modem, using the first network cable. ... 2 Connect one of the router's LAN ports (most routers have four LAN ports) to the computer using the second network cable.


Try this https://www.youtube.com/watch?v=_mQvPzJOQEI it is on you tube it might help

NetGear... | Answered on Apr 08, 2016


Change your password security type from wpa to wep from router wifi device settings.

NetGear... | Answered on Mar 16, 2016


this may be a bit technical ,but stay with me , the address your trying to access is in a different subnet (security reason) the machine your using to access this router has to be in a Ip range of 192.168.254.0
to 192.168.254.253r it will not be able to "see" the device this address is typically used for router config as its not a common used number and so it's unlikely to have any conflicts, however after you config the router , both it and the machines on its network should be set to something in the range of 192.168.1.01 to 192.168.2.254 as this is a more typical range of numbers to use on a small network and should help to eliminate any future config problems as new devices are added in the future

NetGear... | Answered on Feb 27, 2016


If this is a wireless router, your chrome cast device should pick up the signal if within reach. Make sure there is power to the chrome cast. Be sure the router is emitting Wi-Fi signal (test with a tablet or smart phone to make sure). Power cycle both devices (turn off-unplug-wait five minutes-reconnect and switch on) then attempt connection once again.

NetGear... | Answered on Feb 10, 2016


NETGEAR home> router IP address should be assigned as either 192.168.1.1 or 192.168.0.1.
  • Username (all models) = admin
  • Password (current models) = password
  • Password (very old models) = 1234

NetGear... | Answered on Jan 17, 2016


NETGEAR home router IP address should be assigned as either 192.168.1.1 or 192.168.0.1.
  • Username (all models) = admin
  • Password (current models) = password
  • Password (very old models) = 1234

NetGear... | Answered on Jan 17, 2016


I used my computer when I set mine up .

NetGear... | Answered on Dec 24, 2015


What On?

NetGear... | Answered on Nov 30, 2015


Yes! There should be a switch on the top of the router that allows you to turn on/off the wireless feature. A corresponding LED will indicate when it is lit that the wireless is active and when off that the wireless feature is off.

NetGear... | Answered on Nov 24, 2015


  1. In iTunes, choose iTunes > Preferences (Mac) or Edit > Preferences (PC).
  2. Click the Advanced tab.
  3. Click the "Reset cache" button.
  4. Click OK and see if the issue is resolved.
Adjust Parental Controls in iTunes:
  1. Open iTunes.
  2. Access iTunes preferences:
    1. On a Mac: From the iTunes menu, choose Preferences.
    2. On a Windows PC: From the Edit menu, choose Preferences.
  3. Click the Parental Controls tab.
  4. Remove restrictions on Parental Controls.
visit the CBR Tech Solutions

NetGear... | Answered on Nov 10, 2015

Not finding what you are looking for?
Computers & Internet Logo

22 questions posted

Ask a Question

Usually answered in minutes!

Top NetGear Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Mike

Level 3 Expert

4363 Answers

Are you a NetGear Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

WG NetGear

  • WG NetGear

Most Popular Question

wireless network adapter not working

  • Computers & Internet
Loading...