20 Most Recent Kenmore Professional SR365S Iron with Auto Shut-off Questions & Answers




Hi,


Here is a tip that will help you with cleaning the sole plate of your iron...

Cleaning a Steam Iron Soleplate


heatman101


=////////////////////

Kenmore... | Answered on Feb 04, 2011


This usually happens for one of a few reasons, Check, Thermal Fuse, Check Element, Check, on/off switch. Check power cable, for continuity.Check Thermostat, Thats all there is inside an iron, Power comes in the Phase, the Black, or Brown wire, then, through the on/off switch, through a Thermal fuse, through the thermostats contacts, to the element, and the other side of the element goes to the Neutral return. usually White or Blue.of course the Earth is Green or Green/Yellow, stripe.and is connected to the metal case..

Kenmore... | Answered on Apr 23, 2010


switch may be damaged

Kenmore... | Answered on Apr 20, 2008


The message refers to a component that is reading out of the normal temperature range so your theory regarding storage could be correct.

Kenmore Irons | Answered on Jul 03, 2017


Try putting in some LimeAway (Home Depot carries it) and let it sit overnight. Then turn it on to steam and press the steam button to get the steam through the bottom holes etc. Do this on top of some old rags. Then do it again with just water to clear out the LimeAway, should get most of the calcium out. One tip use distilled water in it instead of tap water, you'll get much less buildup. Get distilled water at any retailer about $1 per gallon.

Kenmore Irons | Answered on Jan 01, 2015


  • While these irons are a great name (Kenmore) this one has a crack somewhere in the reservoir and this is not repairable as the reservoir does not detach from the iron itself. If you want to be able to have steam while ironing then you will need to get a new iron.

Regards, Tony

Kenmore Irons | Answered on May 17, 2011


hello If you have an multimeter you can measure the continuity of the heating element of the iron.Set the multimeter to the resistance reading put the test probe black and red to the plug of the iron line 1 and line 2 switch the iron to its full temperature control the meter should read 0000 it means that the heating element is good if the meter reads 0.L it means that heating element is open and needs replacement...the common failure in an iron is the switch(temperature control switch) there is two screws at the back of the iron near the cord open it and check the switch clean the contacts there is also an adjustment in it use a flat screw to adjust the sensitivity of the switch.In some Iron it they use a thermal fuse for safety.here's the picture of thermal fuses..this thermal fuse.is connected in series at the AC power input of the iron locate for it and replace it.use replacement of the same rating...good luck and let me hear if you have further question.. alpug_60.jpg

Kenmore Irons | Answered on Apr 20, 2011


Generally, it means that the bobbin is too tight in the cavity.

1. Remove the bobbin
2. Try a drop of oil in the bobbin cavity in the machine, using a Q-TIP
3. After applying the oil, use a clean Q-TIP to remove excess oil in the cavity (may need more than one clean Q-TIP).
4. Replace bobbin.

(I'm sure you already tried differenty thread)

Hope this helps!

Kenmore Irons | Answered on Sep 03, 2009


A power surge caused by plugging it in burned out the "dial".

Irons | Answered on Oct 29, 2019

Not finding what you are looking for?
Kenmore Professional SR365S Iron with Auto Shut-off Logo

Popular Tags

3 questions posted

Ask a Question

Usually answered in minutes!

Top Kenmore Irons Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Brad Brown

Level 3 Expert

18110 Answers

Are you a Kenmore Iron Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kenmore Irons

  • Kenmore Irons

Most Popular Question

shut off when push red button

  • Irons
Loading...