20 Most Recent Bissell 6595 Lift Off Bagless Upright Vacuum Questions & Answers


YES! If you haven't contacted Bissell yet (or bought a new vacuum) do so. They sent me a nice refurbished machine for free.

Bissell 6595... | Answered on Aug 18, 2017


Hair and dust will work its way under the endcaps of the brushroll causing friction which can melt the brushroll and get hot enough to melt the nozzle housing as you have found. You will need to remove the endcaps to clean the debris out before it causes damage. I don't believe the endcaps are removable on your model. It will save you a lot of money in the long run to purchase a new vacuum that has a metal brushroll with removable endcaps. I have a durable long lasting Riccar vacuum with a metal brushroll available at ThatVacGuy.com. With this model you can pull the brushroll out once a year to clean it and install a new belt. With simple routine maintenance you can do yourself this model will perform great for many years.

Bissell 6595... | Answered on Mar 17, 2017


Hello
At the web link below you will find an exploded view of the Vacuum, the items I think you refer to are 17 and 18 in the picture, neither part is available anymore, the rubber part that you called an "O" ring is a rubber cushion and fits inside the plastic housing above the motor to cushion the motor and isolate vibration. If this is not correct please advise what numbers in the diagram you have a problem with, there are 2 motors, one for suction and one for the brushes, item #30.

http://www.searspartsdirect.com/partsdirect/partsdirect/showSubComp.pd?imageUrl=http%3a%2f%2fc.searspartsdirect.com%2flis_png%2fPLDM%2fP0510254-00001.png

Bissell 6595... | Answered on Jan 28, 2011


this is caused by a dirty air filter and/or a blocked vacume hose ( most of the time the blockage is at the bend where the hose enters the floor sweeper area ) ---
remove and tap out and brush the filter ( or use a air compressor to blow out filter ).
then with the vacume on its side - remove the bottom plate ( like you were going to change the belt ) and use a coat hanger and clean out the hose between the floor sweeper and where the suction hoes attaches. this will restore your vacume to full operation.

c...

Bissell 6595... | Answered on Jan 23, 2011


Remove the brush from the machine and clean as best you can. At each end of the brush there is a plastic clip that holds it into the vacuum. Add some WD40 between the clip and the brush and turn the clip around the brush until it moves freely. Do this for both ends. Reassemble making sure the belt is properly installed.

Bissell 6595... | Answered on Oct 13, 2010


I would check out ebay first you could save a lot of money that way instead of paying retail

Bissell 6595... | Answered on Jan 24, 2010


something is binding ... i dont know what ... you will have to remove all parts and reinstall again. Make sure the bearings spin on the brush when it is out ... remove all hair and string.

good luck ... im sure it is someething simple.

Bissell 6595... | Answered on Nov 10, 2009


OK - so your brush roller is jammed. And yes, the belt is melting! Unplug the machine, remove the belt (you will need another new one anyway) then see if you can turn the roller by hand. If it turns freely without you doing anything else, then you may have put the new belt in incorrectly. However, you will probably find you can't turn it, or it's hard work (it should rotate freely). Remove the roller and check the bearings - there may well be something tangled up at one end of the roller. If you can get the roller rotating freely, all should be well.
Good luck

Bissell 6595... | Answered on Mar 08, 2009


Check the ball that pops up up when the waste tank is full. If you don't clean the machine thoroughly the last time you used it, they stick.

Bissell Vacuums | Answered on Feb 16, 2020


Yes. Under the front handle yoke. The “no spray” is caused by a build up of soap from the wire. You might have to clean out the spray tubes on the bottom. Try running warm water with no soap after cleaning.

Bissell Vacuums | Answered on Feb 03, 2020


check back of nozzle housing for reset on kenmore upright

Bissell Vacuums | Answered on Jan 26, 2020


Try descaling it, as long as the heater is working.

Bissell Vacuums | Answered on Jan 13, 2020


Check for any clogs in the hose and belt areas

Bissell Vacuums | Answered on Jan 05, 2020


sounds like the shaft might have lots of hair wrapped on it and that acts like a brake . get a really sharp dental pick and check for hair

Bissell Vacuums | Answered on Dec 13, 2019

Not finding what you are looking for?
Bissell 6595 Lift Off Bagless Upright Vacuum Logo

Popular Tags

16 questions posted

Ask a Question

Usually answered in minutes!

Top Bissell Vacuums Experts

Brad Brown

Level 3 Expert

18166 Answers

CJ C
CJ C

Level 2 Expert

66 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Bissell Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Bissell Vacuums

  • Bissell Vacuums

Most Popular Question

trying fix bissell

  • Vacuums
Loading...