20 Most Recent HP LaserJet M4345 MultiFunction Printer - Page 5 Questions & Answers


Upgrade the firmware.Go to http://www8.hp.com/us/en/support-drivers.htmlEnter your printer.Select your operating systemSelect the firmware and download it. Follow the instructions to the letter

HP LaserJet... | Answered on Apr 30, 2012


13.20.00 = The pre-feed sensor (PS102),the top-of-page sensor (PS103), or thefuser-delivery sensor (PS108) detectedmedia inside the MFP when it was turned on.
Follow the instructions in the display screen

HP LaserJet... | Answered on Apr 30, 2012


here you can find your answer.https://content.etilize.com/User-Manual/1010130791.pdf

it`s the user guide manual.
here you can find how to use your HP M4345.Hope it`s useful.

HP LaserJet... | Answered on Apr 24, 2012


Do you have internet access in you system, if not you cannot access to jetadmin, check internet permissions, I don't think so its printer side problem, take help from system administrator to solve this issue..

HP LaserJet... | Answered on Feb 04, 2012


50.2 is a fuser warmup error.
If you have technical experience with printers, reseat the fuser.
Problem could be the fuser, the DC Controller or the power supply.
Have someone that works on printers take a look at it. If you haven't
done it before, you arn't going to be able to replace the DC Controller or power supply.

HP LaserJet... | Answered on Dec 30, 2011


Check inside the MFP (manual feed tray) for a scrap or a whole sheet of paper.
There is one of three sensors that is sending a paper jam notice to the printer.

HP LaserJet... | Answered on Nov 06, 2011


Printer/MFP in stand alone condition remove the JetDirect Card if equipped, the hard drive if equipped, fax card if equipped and any HP paper handling accessories. In addition, if applicable all third-party DIMMs (leave the minimum HP memory installed) and all third party solution components and/or accessories should be removed Install one by one check which device having faulty, replace it..After replacing the part check firm ware loaded in the printer if its lower version than present one up load latest firm ware..

HP LaserJet... | Answered on Oct 28, 2011


Primary level replace DC controller, seconderay level Formatter.. Badly no other way to escape from this issue.

HP LaserJet... | Answered on Sep 22, 2011


Add Zetdirect card 620N & above, configure it then check.. this is the easiest way escape from this issue.

HP LaserJet... | Answered on Sep 14, 2011


You might have a dislodged flag but your error is sort of cryptic. Is it the ADF feeder, the manual tray feeder? More details might enable me to answer your question better. Check all the flags in the paper paths to ensure that they move smoothly and are not stuck in one position.

HP LaserJet... | Answered on Sep 03, 2011


Hi!

According to HP service manuals, the error you described is in the category:

JAM INSIDE TOP COVER AREA

and more specific:

The pre-feed sensor, the top-of-page sensor, or the fuser-delivery

Those are the points where some paper pieces or even dust can be stuck.


Hope it helped,

Bogdan

HP LaserJet... | Answered on Aug 30, 2011


If you are setting the trays for non-plain paper then you need to ensure that your print driver is set to match the paper types that are set on the printer. Otherwise the printer will always ask you to confirm which paper you want to print on.

HP LaserJet... | Answered on Aug 10, 2011

Not finding what you are looking for?
HP LaserJet M4345 MultiFunction Printer Logo

205 questions posted

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

LaserJet HP

  • LaserJet HP

Most Popular Question

cold reset hp m1132 mfp printer

  • Office Equipment & Supplies
Loading...