20 Most Recent ViewSonic VX2235wm LCD Monitor Questions & Answers


You need to chk graphics settings in NVidia control center and change resolution until it looks right

ViewSonic... | Answered on Mar 06, 2017


Sounds like a power supply failure. Send it in for service.

ViewSonic... | Answered on Feb 08, 2015


Use very thin screw driver to pop up the front bezel but do not completely remove the bezel, just enough to pop the back off when you place the front of the monitor on the table top facing odwn on top of a towel. It is a little hard for me to explain in words. You can also serach YOUTUBE.
See vx2255 which is the same chassis.
http://s807.photobucket.com/albums/yy352/budm/Viewsonic%20VX2255W/

See other pictures in my albums also.

ViewSonic... | Answered on Nov 13, 2014


Hi there, unfortunately bad news it is panel defect. The only solutions should be to replace it. If you are not familiar with electronics please do find proper service personal for that.
Thanks.

ViewSonic... | Answered on Mar 08, 2014


Hello,

The most common issue with this model is a bad power supply board. Here is a link to a repair guide that will show you how to dis-assemble the unit and what to look for and replace to repair the board and get the units back up and running again (easy repair).
http://www.ccl-la.com/blog/index.php/repairing-the-viewsonic-vx2235wm-lcm-monitor/
I hope this helps, if so please rate my solution.

If you have any more questions just click on my profile and send me a direct question.

BuddyMc

ViewSonic... | Answered on Dec 16, 2013


Based on the specs it looks like this monitor is a CFL type and not a LED type. That means it uses a inverter to power the CFL tubes in the LCD. Usually these go bad after awhile.. usually the capacitors on the board run dry or go bad and need to be replaced. If your not good with soldering you might be able to find a board to replace it with.. more then likely given the monitor size "small" the inverter board is usually built-in on to the power supply board or mainboard and will need to be replaced together but some times comes seperate as it's own board. You might just consider replacing the monitor, LED monitors are pretty cheap now a days and more energy efficient.. and should last longer then most CFL type monitors because they don't use as much current and don't produce as much heat and LEDs tend to last longer with out the yellowing effect of CFLs. However it really comes down to build quality & component quality. While the most likely cause is a bad inverter other things can cause this too..like a bad mainboard sending voltage signal lower then normal to the inverter board.

ViewSonic... | Answered on Nov 06, 2013


Dear Miguel,
I think this problem came from some Capacitor of the monitor. I solved this problem with my Viewsonic VG2021M and I hope it should help you too.
Please check the link : http://www.fixya.com/support/t6862769-keep_pressing_off_button
I will follow this problem and will try to help anyway I can.
VirtualSyS

ViewSonic... | Answered on Jul 24, 2013


Hello,

This is a very common problem with this model after a few years of use. This problem is caused by a failure of the capacitors in the power supply board hat powers up the back lights in the monitor. When the back lights don't power up you get no display on the screen. Here is a link to a repair guide for that model that shows how to open the unit and what to look for and replace to repair the monitor.

http://www.ccl-la.com/blog/index.php/repairing-the-viewsonic-vx2235wm-lcm-monitor/

Here is part one of the three part video repair guide posted at the above link:


ViewSonic... | Answered on Feb 09, 2013


This really sounds like you have a power supply board that is having problems with the filter capacitors which are causing it to not start up correctly. Here is a like to a repair guide including video instructions showing how to open and repair the monitor.

http://www.ccl-la.com/blog/index.php/repairing-the-viewsonic-vx2235wm-lcm-monitor/

Part one of the video guide:

ViewSonic... | Answered on Feb 09, 2013


That is a power supply problem not a video board problem. You will need to either rebuild or replace the power supply to fix that problem.

ViewSonic... | Answered on Oct 22, 2012


The most common cause of power issues with this unit are capacitors on the power supply board. This is an easy repair. Here is a link to a repair guide with full instructions showing how to open the monitor and what to look for and replace to rebuild the power supply board and revive the monitor.

http://www.ccl-la.com/blog/index.php/repairing-the-viewsonic-vx2235wm-lcm-monitor/

I hope this helps.

ViewSonic... | Answered on Jun 11, 2012


Look for bad caps as shown in my pictures here:
http://s807.photobucket.com/albums/yy352/budm/Viewsonic%20VX2235W/
If you are going to DIY and have proper tools and know safety precaution then please read on:
Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply, blown fuses; poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed monitors to get some ideas what to look for: http://s807.photobucket.com/home/budm/allalbums
Post back what you see inside so we can guide you further and it will help out other people in the future also.
http://en.wikipedia.org/wiki/Capacitor_plague
http://www.badcaps.net
Capacitors kit: http://lcdalternatives.auctivacommerce.com/

ViewSonic... | Answered on Jan 29, 2012


Here is a link to a repair guide with pictures and videos showing how to open the unit and then repair the power supply board that is the most common cause of issues in the VX2235wm monitor.

http://www.ccl-la.com/blog/index.php/repairing-the-viewsonic-vx2235wm-lcm-monitor/


I hope this helps, if so please rate my solution.

BuddyMc
1_29_2012_10_17_36_pm.jpg

ViewSonic... | Answered on Jan 29, 2012


Make sure your computer's screen resolution is fine for that when you power up the computer press F8 key 5 to 6 time untill you can see safe mode and other menu if you are able to see safe mode then enter in enable vga mode then enter as admnistrator go to control panel->display property ->settings change screen resolution to 1024*768 then apply and restart it.Let me know if you need further assistance.Thanks for using FixYa.

ViewSonic... | Answered on Nov 23, 2011

Not finding what you are looking for?
ViewSonic VX2235wm LCD Monitor Logo

150 questions posted

Ask a Question

Usually answered in minutes!

Top ViewSonic Computers & Internet Experts

Ekse

Level 3 Expert

13434 Answers

Cindy Wells

Level 3 Expert

6073 Answers

Dimitar Todorov

Level 2 Expert

240 Answers

Are you a ViewSonic Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

ViewSonic Computers & Internet

  • ViewSonic Computers & Internet

Most Popular Question

green vertical line appears left side

  • Computers & Internet
Loading...