20 Most Recent
GE Security Simon 3 Wireless Home Security System Questions & Answers
1 Answer
I keep getting a false allarm from one of my
Double check the alignment of the sensor and magnet, the house may have settled and the alignment may have changed enough to show the fault / set the alarm off. There should be a notch or series of notches on the transmitter, make sure the magnet is centered on that. Also make sure the gap between the two is as small as you get it and still able to operate the windows (both vertically and horizontally). If all that checks out, you could have a tamper switch (GE uses a spring to hold it down) that is not getting fully depressed. or, you may have a bad transmitter. If it is the spring, you may be able to stretch it out a little to ensure good pressure on the tamper switch.
GE Security...
|
Answered
on Apr 09, 2018
1 Answer
I recently installed a GE
Check the outlet to ensure it :1- has power , 2- is not a switched outlet. Check your wire connections to ensure they are secure. If all of the above are good, the transformer may have shorted when disconnecting. Use a voltage meter on the transformer terminals and the AC scale, check the output of the transformer.
GE Security...
|
Answered
on Jun 09, 2017
1 Answer
Low battery and Phone communication failure
Check that you are not using an app that is continuously accessing the internet and communicating with a server for some reason that is using the phones WiFi or mobile channel. This will drain battery life if incorrectly configured etc ( i.e selecting access to your location, services and other info )
GE Security...
|
Answered
on Apr 02, 2017
1 Answer
GE simon security system
Depends. Do you mean the chime? If all that is missing is the chime whenever a zone is tripped then simply press the CHIME button on the front panel. If it is lighted solid red then your chime is on and it will talk to you. If chime is off then it wont talk to you at all when a zone is tripped. Good luck.
GE Security...
|
Answered
on Jan 02, 2017
1 Answer
I have a GE home
It might not hurt to try the "Microsoft Solution" and reboot the system. First disconnect the AC power then disconnect the battery. Wait 1 minute then reconnect the battery and reconnect the AC power.See ifyou can arm and disarm the system. Then reconnect the siren and try again to arm and disarm the panel. If the keypads beep it can usually give you an error code that will help you pinpoint the problem.
GE Security...
|
Answered
on Dec 26, 2015
1 Answer
I have an old Westinghouse Security Systems that
Check all ur windows and doors sensoring connections,might need to be changes.Weather is too hot or too cold,will trigger the alarm.When u arming tries by passed and any error codes for doors or windows connections codes.This should stop the fault alarm by the expanding and contracting sensors by the weathers.
GE Security...
|
Answered
on Dec 26, 2015
1 Answer
How do you remove the control panel on Simon 3?
There is a couple steps in removing this panel. First, unplug the unit and then locate the tab on the top of the unit, it has to be pushed down. When the tab is pushed down the first faceplate should drop down, exposing the keypad with the menu options. Second, you need to get a small flat head screwdriver and put it under the clip at the top of the panel. You can locate it by finding where your pushed the original tab down; it's right below that. Once you have your screwdriver under the small clip, push the clip up and pull the 2 faceplate towards you. Finally, after the second plate is down, unscrew/unplug the wires from the panel, unscrew the mounting panel and your done! Beware, depending on how your alarm is hooked this can cause a short to your household telephone lines causing them not to work!
GE Security...
|
Answered
on Aug 03, 2015
3 Answers
Don't have the access code
Do you mean the access code for turning off an alarm or arming the system before leaving? If so, NO. You would have to know the original code to even enter programming to change the access code. Contact your realtor and have them get you in contact with the previous owner. Find out the code from them. If they properly removed their code before moving from the house use the default code, 1234. Good Luck.
GE Security...
|
Answered
on Apr 18, 2015
Not finding what you are looking for?