20 Most Recent Stanley 100 ft. Tape Measure, FatMax Questions & Answers


check coil spring inside might be broken or disengage to the tape measure.

Stanley 100 ft.... | Answered on Nov 29, 2009


You could do a bit of research as i can't remember the math's from my college days, but, it is possible to calculate the distance something travels by using its rate of descent against the time it takes to reach the ground, for instance, if gravity is measured at 9.81N/m per sec squared, then an object must speed up at the same rate from standstil every time unless the earths gravitational pull changed. If you then timed how long it takes to hit the ground you could do a simple calculation offsetting the rate of descent against time which would then give your distance. The calculation is - distance = speed x time, but you would need to factor in the the rate of change in the speed of the object from standstill to finish which is the bit i can't remember.

Stanley 100 ft.... | Answered on Oct 31, 2009


the electronic sensor eyes being off are the most common cause of this.

They need to be pointed at each other so they can "see" each other.

Commonly, the units have a light on them that will illuminate when they can see the other half of the unit on the the other side.

Also check the terminals that the sensors connect to, and make sure that they are connected.

Stanley 100 ft.... | Answered on Oct 27, 2009


you should be able to ----- how far to your nearest toolking store? you can still deal with them no matter where you are ---I deal with them all the time ,and I`m in australia

Stanley 100 ft.... | Answered on Sep 05, 2009


We Use Debruce Polish on all our cooktops. Debruce also works on stainless steel, polished granite, marble, porcelain, formica, enamel and glass. DeBruce is non-toxic odor-less and eco-friendly. You can get DeBruce on line at debrucepolish.com.


Stanley 100 ft.... | Answered on Aug 24, 2009


Use a second measuring tool and compare the results, or you can measure a known size or length (floor tiles for example)and check the reading you get.

Stanley 100 ft.... | Answered on Aug 21, 2009


You have acouple of options

You can buy a measuring tool that doesn't have a size limit or has a very high size limit, you can check around to find one that will suit your needs.

You can measure the till the end of you measuring tool, mark the spot where it ends, and make another measuerment from that spot.

Another option is to take a long piece of string, and run it between the two points you want to measure, Cut the rope exactly between the two points, and later you can measure it, section by section, this is a lot of work!

I'm sure that these aren't all the possible methods, I think that folks around here might add a few.

Good luck

Stanley 100 ft.... | Answered on Jun 03, 2009


there is an acrylic post inside that directs a light beam to several different places so when the light beam is broken then it tells other parts that the tape is loaded this could be broken off or if the tape broke off inside a piece could be wrapped around a capstan or drive post causing the machine to think it is at the end of the tape and to turn itself off.

Stanley 100 ft.... | Answered on Feb 13, 2009


Hi, Its sound like your compressor is not turned on. Make sure your compressor is plug in, and the (on and off) switch is turned on. Check the pressure gage to see what psi you have. You need at lease 90psi. If you don't have that much pressure, There should be an adjusting knob below the gage. Turn the knob until you get the proper psi.

If this doesn’t work for you, please write back. Thanks,

Stanley 100 ft.... | Answered on Nov 29, 2008


Press the red button - (distance) you will see a red dot on the wall you are measuring - then you will hear a beep - release the button and read the display - the measurement should be displayed and accurate within a quarter inch.

Stanley 100 ft.... | Answered on Nov 23, 2008


51bc252.jpgThe handle on the right

Stanley 100 ft.... | Answered on Aug 03, 2008


i USE SCISSORS MYSELF

Stanley... | Answered on Nov 13, 2019


stanley fatmax jumpstarter 1000A light wont turn off?

Stanley... | Answered on Sep 09, 2019


Most stud finders have a sensitivity adjustment that should be carefully adjusted per instruction manual before use.
Failure to do this results in erroneous indications.

If you have adjusted exactly per the instructions with the same result the unit is probably faulty.

Stanley... | Answered on Apr 04, 2019


WHY HAVE YOU NOT TRIED IT TO FIND OUT FOR YOURSELF .

Stanley... | Answered on Mar 26, 2019


here is the website:
https://www.stanleytools.com/products/hand-tools/flashlights-lighting/spotlight/waterproof-led-rechargeable-spotlight/fl5w10
and they say the warranty is 1 year:
Warranty
1 Year Limited Warranty
The manufacturer, Baccus Global warrants products against defects in materials and workmanship for a period of ONE (1) YEAR from the date of retail purchase by the original end-user purchaser ("Warranty Period").
If there is a defect and a valid claim is received within the Warranty Period, the defective product can be replaced or repaired in the following ways: (1) Return the product to the manufacturer for repair or replacement at manufacturer's option. Proof of purchase may be required by manufacturer. (2) Return the product to the retailer where product was purchased for an exchange (provided that the store is a participating retailer). Returns to retailer should be made within the time period of the retailer's return policy for exchanges only (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. Please call 1-877-571-2391 for more information or return instructions.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal wear and tear, accidents; damages sustained during shipping; alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to follow instructions for care and maintenance for the product.

O
Otherwise, check with the seller who sold it to your wife - If they are unwilling, and more companies seem to be going this route, go to the Manufacturer

Stanley... | Answered on Mar 04, 2019


Yes. Unless one was provided the standard is to just use an extension cord.

Stanley... | Answered on Feb 11, 2019

Not finding what you are looking for?
Stanley 100 ft. Tape Measure, FatMax Logo

14 questions posted

Ask a Question

Usually answered in minutes!

Top Stanley Measuring Tools & Sensors Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

Frank Walton

Level 1 Expert

26 Answers

Are you a Stanley Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Stanley Measuring Tools & Sensors

  • Stanley Measuring Tools & Sensors

Most Popular Question

tape measure wont retract

  • Measuring Tools & Sensors
Loading...