Frigidaire Affinity ATF7000E Front Load Washer - Page 3 - Answered Questions & Fixed issues


CHECK THE HOSE RUBBER SEALS GASKETS

Frigidaire... | Answered on Mar 31, 2015 | 57 views


HARDWATER DEPOSITS HAVE U CHECKED THE HOSE RUBBER SEALS

Frigidaire... | Answered on Mar 31, 2015 | 30 views


CHECK THE CAM DOGS IN THE AGITATOR>

Frigidaire... | Answered on Mar 31, 2015 | 19 views


No spin, try these:

Using a multi meter check for continuity the door switch, which when bad may not allow agitation or spin. The lid switch assembly can fail either mechanically or electrically.

Check the clutch, brake assembly and transmission, one way to check for slipping is to get under the machine after a spin cycle ( this is if u get a lil spin but not much leaving clothes still wet) mix in a spray bottle a lil water and some dish detergent, then spray it on the clutch assembly ( the metal round pc. Connected to the tranny) if it sizzles and steams up then u know its bad and slipping. Another way to check clutch if u get no spin at all? Is to take it out and use ur hand to try and turn the inner spring assembly pushing it around the inside? If its very easy, it BAD should be hard to push by hand.


Next check the motor coupler which engages the tub and tranny to the motor. ( if its bad u usually get no wash or spin or very little of either)

Next check for a loose, worn or broken belt if belt driven.

On some front load models u may need to check the STATOR assembly.
The stator is essentially one half of a motor, it interacts with the tub by creating a strong electro-magnet. If the stator burns out the washer won't spin or agitate. Check the stator for continuity. This part is often misdiagnosed.

Frigidaire... | Answered on Mar 31, 2015 | 51 views


ARE U SURE THERE IS NO BLOCKAGE? DID U TRY AND TURN PROPELLER ON PUMP BY HAND AND CHECKL ALL HOSES. IF YES THEN GO TO CHECK THE CLUTCH ASSEMBLY

Frigidaire... | Answered on Mar 31, 2015 | 152 views


No spin, try these:

Using a multi meter check for continuity the door switch, which when bad may not allow agitation or spin. The lid switch assembly can fail either mechanically or electrically.

Check the clutch, brake assembly and transmission, one way to check for slipping is to get under the machine after a spin cycle ( this is if u get a lil spin but not much leaving clothes still wet) mix in a spray bottle a lil water and some dish detergent, then spray it on the clutch assembly ( the metal round pc. Connected to the tranny) if it sizzles and steams up then u know its bad and slipping. Another way to check clutch if u get no spin at all? Is to take it out and use ur hand to try and turn the inner spring assembly pushing it around the inside? If its very easy, it BAD should be hard to push by hand.


Next check the motor coupler which engages the tub and tranny to the motor. ( if its bad u usually get no wash or spin or very little of either)

Next check for a loose, worn or broken belt if belt driven.

On some front load models u may need to check the STATOR assembly.
The stator is essentially one half of a motor, it interacts with the tub by creating a strong electro-magnet. If the stator burns out the washer won't spin or agitate. Check the stator for continuity. This part is often misdiagnosed.

Frigidaire... | Answered on Mar 31, 2015 | 31 views


check ur inlet water valve

Frigidaire... | Answered on Mar 31, 2015 | 70 views


No spin, try these:

Using a multi meter check for continuity the door switch, which when bad may not allow agitation or spin. The lid switch assembly can fail either mechanically or electrically.

Check the clutch, brake assembly and transmission, one way to check for slipping is to get under the machine after a spin cycle ( this is if u get a lil spin but not much leaving clothes still wet) mix in a spray bottle a lil water and some dish detergent, then spray it on the clutch assembly ( the metal round pc. Connected to the tranny) if it sizzles and steams up then u know its bad and slipping. Another way to check clutch if u get no spin at all? Is to take it out and use ur hand to try and turn the inner spring assembly pushing it around the inside? If its very easy, it BAD should be hard to push by hand.


Next check the motor coupler which engages the tub and tranny to the motor. ( if its bad u usually get no wash or spin or very little of either)

Next check for a loose, worn or broken belt if belt driven.

On some front load models u may need to check the STATOR assembly.
The stator is essentially one half of a motor, it interacts with the tub by creating a strong electro-magnet. If the stator burns out the washer won't spin or agitate. Check the stator for continuity. This part is often misdiagnosed.

Frigidaire... | Answered on Mar 31, 2015 | 113 views


Try adding baking soda to the wash. We have the same issues (son works on a dairy farm) and will on clothing resort to chlorine bleach even on colors in small amounts. Eric

Frigidaire... | Answered on Mar 21, 2015 | 277 views


Good Afternoon friend, thank you for your post!

I understand that water is not entering your Frigidaire Affinity washer. If the washing machine thinks that the door or lid is not closed, the water will not enter the machine. I recommend that you verify that there are not any visible defects with the door latching mechanism. I also recommend that you visually inspect the water inlet hose to make sure that it is not twisted or restricted. Lastly, please verify that the water supply faucet is completely open and not closed. You may want to avoid running water in other areas of your house while the washer fills. If these troubleshooting steps do not resolve your issue, I recommend that you allow a professional to properly diagnose your washer for you in order to avoid purchasing any unnecessary parts. -NS

Frigidaire... | Answered on Mar 06, 2015 | 87 views


sometimes coins get stuck in the pump which causes noise when draining. Front of machine has to come off and pump taken apart and cleaned out.

Frigidaire... | Answered on Mar 02, 2015 | 60 views


Hello friend, thanks for your post!

From my understanding you would like a list of error codes that apply to your Frigidaire washer. Is there a specific error code you are searching for? I was unable to locate a list of all the codes that would be available within your washer, ATF7000E. With additional information I would be able to assist you further. -Matt

Frigidaire... | Answered on Feb 18, 2015 | 133 views


The rear bearing for the drum needs to be greased. If you don't grease it and ignore it, eventually the dryer will stop working because you will be overloading the motor, and the motor will start drawing additional current that it will trip the breaker. Greasing the rear bearing is a 15 minute job. You need to purchase high tempo grease. Frigidaire sellsthe high trmp grease that is required.

Frigidaire... | Answered on Jan 05, 2015 | 962 views


Most likely suspect is the heating element. Part runs under 100 dollars. If you can't do the repair yourself, prepare to spend at least twice that amount.

Frigidaire... | Answered on Nov 30, 2014 | 184 views


Hi, Unplug the unit from AC power for 30 seconds to 1 minute, This should reset it back to the defaults. Good Luck!

Frigidaire... | Answered on Nov 02, 2014 | 336 views


mi lavadora da e91 y key stuk que hago

Frigidaire... | Answered on Oct 24, 2014 | 333 views


Hello friend, thank you for your post!

I understand that you would like to remove the front cover on your Frigidaire washer. Your question is labeled under model ATF7000E I was able to locate the parts manual for that appliance that shows a parts breakdown inside of your washer but no instruction guide to disassemble the front panel. I hope this information helps to some degree. -Matt
Frigidaire Manual Search Results

Frigidaire... | Answered on Oct 02, 2014 | 128 views


Hello friend, I appreciate your post!

If the control panel is not lighting inside of your Frigidaire washer it could need to be replaced. I would recommend reaching out to a professional, if you do not have a professional connection you can visit the manufacturer website to find a service provider in your area. Hopefully this is helpful. -Matt

Frigidaire... | Answered on Sep 25, 2014 | 86 views

Not finding what you are looking for?
Frigidaire Affinity ATF7000E Front Load Washer Logo

1,529 questions posted

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

J. Bradshaw

Level 2 Expert

121 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...