Frigidaire Affinity ATF7000E Front Load Washer - Page 4 - Answered Questions & Fixed issues


Hey friend, that's a great question!

It sounds like you may have an issue with the door strike or door latch on your Frigidaire front loader. I would recommend contacting a professional to come out and properly locate the reason to why your door is unlocking before going into a cycle. -Matt

Frigidaire... | Answered on Sep 25, 2014 | 62 views


Vanessa,

I will share a link with you that may put you happy and enthusiastic. It serves, as well as, a contact point for reasonably priced parts ; should you need them. Frigidaire Affinity Washer Disassembly . Take a look. And please share how you finished. Fare.Well.

Frigidaire... | Answered on Sep 23, 2014 | 202 views


To Stranded,

Here is a link that will put you directly to free support and a manual to guide through the trouble shooting function. sparke needs help with Frigidaire Washer on ManualsOnline com . If you are familiar with a meter to troubleshoot and identify voltages. Start there. If the display is functional. Here is another forum you can tap for resources to compare. Basics first. How to enter diagnostic mode on Frigidaire ATF7000 washer Appliance... .
And you will need to take it apart.. here is the link for that solution.
Frigidaire Affinity Washer Disassembly

Say how you made out and if this approach helped please?

Fare. Well.

Frigidaire... | Answered on Sep 23, 2014 | 347 views


Hello friend, thanks for your post!

It sounds like it could be a possible issue within your control panel or door lock assembly. If the door is not making that connection it is closed the washer will not start. I would recommend having a professional come out to properly diagnose your appliance to avoid any unnecessary part purchases. -Matt

Frigidaire... | Answered on Sep 16, 2014 | 93 views


Hello keisha, thank you for your post!

I understand that your Frigidaire washer is making a buzzing sound until the cancel or start button has been pushed. It sounds like it could be a possible issue within the door either not being fully closed or it could be a defective switch. I would recommend resetting your appliance which can be done by disconnecting power to the appliance for roughly ten minutes. Please comment back if that did not help correct the issue. -Matt

Frigidaire... | Answered on Sep 09, 2014 | 325 views


Good Afternoon Friend, this is Z. I am happy to assist you!

If your washer continues to PAUSE, it commonly indicates that the door of your washer is not securely latched or the cycle has been interrupted. Try pressing "PAUSE/CANCEL" or "START/PAUSE" once to resume cycle. If these basic troubleshooting tips prove ineffective, try reprogramming your appliance by unplugging it or flipping the household circuit breaker off. It is best to wait approximately ten minutes and then turn on your washer. If the issue persists, then your washer could possibly have a faulty door latch or experiencing a communication error with the control board. I would personally contact a professional to accurately diagnose your washer to determine the root cause to reduce the risk of unnecessary parts. Best!

Frigidaire... | Answered on Sep 09, 2014 | 132 views


Hello Friend, thank you for your inquiry!

Based on the symptoms you are describing, it sounds like your Frigidaire washer may either be experiencing a communication error from the main control board or the timer itself may not be operating correctly. Do you notice a humming noise? If so, then it may be a clogged drainage hose or pump that needs to be cleaned, or it could possibly have another issue with the door lock assembly. I would personally contact a professional to accurately diagnose the washer to determine the root cause to reduce the risk of unnecessary parts. Best regards! - Z

Frigidaire... | Answered on Oct 19, 2014 | 143 views


clean it by using 5 cups bleach fill soap cup put rest in tub wash in hot water long cycle run another or 2 after to make sure bleach is gone

Frigidaire... | Answered on Sep 08, 2014 | 118 views


Hello Larry Occhipinti, thank you for your post!

If you are pushing the necessary buttons on your Frigidaire washer to perform a system clean and they are not working, it could be a possible issue within the control panel. I would recommend a reset on your appliance which can be done by disconnecting power from your appliance for roughly ten minutes. If that does not correct the issue, you can run a hot water wash cycle with a cup of bleach inside the tub to clean your appliance out as well. I hope this is helpful. -Matt

Frigidaire... | Answered on Sep 03, 2014 | 1,111 views


Hi Friend, thank you for your inquiry!

If you are receiving an error code PAUSE, it commonly indicates that the door of your washer is not securely latched or the cycle has been interrupted. Let's try pressing "PAUSE/CANCEL" or "START/PAUSE" once to resume cycle. If these basic troubleshooting tips prove ineffective, try reprogramming your appliance by unplugging it or flipping the household circuit breaker off. It is best to wait approximately ten minutes and then turn on your washer. If the issue persists, then your washer could possibly have a faulty door latch or experiencing a communication error with the control board. I would personally contact a professional to accurately diagnose your washer to determine the root cause to reduce the risk of unnecessary parts. Best - Z

Frigidaire... | Answered on Sep 02, 2014 | 119 views


Good Morning Friend, this is Z. I appreciate your post!

From what you have described, it sounds like your washer cannot properly drain and dispose of the water and detergent solution. Does your washer make a humming noise? If so, the drainage hose/pump may be clogged and needs to be cleaned. If not, your appliance may possibly be experiencing an issue with the door lock assembly, faulty pump, timer or control board not communicating correctly. In this case, because it could be a number of any one of several underlying causes, I would recommend contacting a professional to properly diagnose and repair your washer. Best!

Frigidaire... | Answered on Aug 28, 2014 | 119 views


The belt might be out of alignment or broken.

Frigidaire... | Answered on Aug 08, 2014 | 67 views


Hello friend, thank you for your post!

I see you are asking for help with a door sensor for your Frigidaire washer. What exactly are you asking for in regards to the door sensor? I would need some additional information in order to provide you accurate assistance. I look forward to helping you. -Matt

Frigidaire... | Answered on Aug 01, 2014 | 123 views


Good morning friend, I appreciate your post!

I understand that your Frigidaire washer will start but after 30 seconds it will cut off and all your indicator lights will flash. It could possibly be a miscommunication with the board I would try to reset your appliance, you can do this by unplugging the power cord or flipping the household circuit breaker for ten minutes. Could you comment back I would like to verify if that helped? I look forward to your response. -Matt

Frigidaire... | Answered on Jul 31, 2014 | 51 views


Hey friend, thank you for allowing me to assist you!

It is normal to have water in the tub after your Frigidaire washer has completed the final spin cycle. The water that is in the tub is there to help prime the pump. Hope this information is helpful. -Matt

Frigidaire... | Answered on Jul 29, 2014 | 132 views


Hi Mike,

Here is the checklist for the machine. Frigidaire ATF7000ES Use And Care Manual Avoid Service Checklist .

Go here to see how someone else solved and reported his findings
Frigidaire washing machine Affinity ATF7000E The Laundry Appliance...


The lint screen may be blocking. Clean it. The last link saves me the time to explaining. I am glad he shared.



Please leave feed back? The more we practice the better we become. Fare. Well.

Frigidaire... | Answered on Jul 27, 2014 | 91 views



Hey friend, that's a great question!

I am presuming you are speaking about the backflow preventer. This is designed to help when the water is pushed out of the pump. Therefore, it is typically normal that the sheath is in your drain pump. Hope this helps. -Matt

Frigidaire... | Answered on Jul 24, 2014 | 55 views


Good afternoon friend, thank you for your question!

I see you are trying to change the door sensor on your washer model ATF6000FS0. Please describe what your appliance is doing so that I can assist you better in pinpointing the problem before you take this step. I look forward to your response. -Matt

Frigidaire... | Answered on Jul 24, 2014 | 65 views


There is a special type of pliers used for car's radiators clamps, you can buy them in most autoparts(they are sheep) You can use regular sliding adjustable pliers but I won't recomended it will be very hard to do it that way. Good luck Rodolfo Perez (RUDY)

Frigidaire... | Answered on Jul 21, 2014 | 23 views


Hi Friend, this is Z. Thank you for allowing me to assist you!

I see that your question is listed under Frigidaire washer, ATF7000E, and it is not filling with water or draining. Please confirm that the house valves are fully turned on. Otherwise, typically, faulty switch does not allow the valve inside to turn or a kinked fill hose. Other possibilities of more potential serious issues are water valve faults, faulty control board, pressure switch or wiring failure. If I was in your position, I will personally consult a professional to move forward accurately and assist with the repairs.

Frigidaire... | Answered on Jul 21, 2014 | 45 views

Not finding what you are looking for?
Frigidaire Affinity ATF7000E Front Load Washer Logo

1,529 questions posted

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

J. Bradshaw

Level 2 Expert

121 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...