Hobart HL200C Mixer - Answered Questions & Fixed issues


Hi. Your A200 is in need of service. The grease's lifespan has expired. There are two ways of doing this. First, the expensive way. Call for a Hobart Tech to come and service the mixer. This will take about 4-5hrs to service at a rate around $100.00usd per hour, plus the cost of parts. He/she will need to change all seals, remove old grease and oil, check all bearings and gears for excessive wear and replace as necessary, this includes the planetary gear.

Now for the affordable solution. Unplug the mixer, remove the top cover. Gently use a small screwdriver to pry off the two circular metal dust caps found on the transmission housing, use a good flashlight to determine, through these openings, the quality, quantity and condition of the grease inside the transmission case. If there's a lot of oil you can remove much of it a bit at a time by using a wire coat hanger to which you can attach bits of cloth to absorb as much oil as you can. Once oil is removed, add new grease through these same holes until full (Chevron FM ALC EP-2, food grade lube). Run the mixer for a couple of minutes to distribute the new grease. Fill to the top once again and replace dust covers. Remove planetary, clean, inspect change seal and re-grease.

OPTION (mechanically challenging) You can do a more thorough job by removing the trans. cover completely, removing the 3 gear shafts inspect all bearings and gears, change seals on mainshaft and planetary. Remove old grease and oil, clean gearshafts and gears. Parts drawings are available from www.hobartservice.com It's free to register and then locate your parts drawings. Be sure that you have the correct files for your Model #, ML# if there is one and Spec.#, all found on the info plate.

When disassembling, take a digital photo of every step and lay the removed components on a piece of cardboard in the removed sequence. These practices will become valuable during re-assembly.

If this solution has assisted you, please rate it. ricardok45

Hobart HL200C... | Answered on May 15, 2018 | 9,186 views


hello! the speed select switch is defective...It is located behind the timer control board...Part # is...00-874831


Guru.............saailer


I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

Hobart HL200C... | Answered on Apr 01, 2011 | 246 views


Here is the complete manual of parts with exploded views and part numbers:
http://www.wasserstrom.com/wcsstore/ExtendedSitesCatalogAssetStore/Attachment/item%20680610.pdf

Good luck and thank you for using FixYa! We would sure appreciate a 4 "thumbs-up" rating for this FREE answer. Happy holidays!

Hobart HL200C... | Answered on Dec 05, 2010 | 175 views


Motor start capacitor failed or start run switch mounted at back of motor housing damaged

Hobart HL200C... | Answered on Nov 13, 2009 | 217 views


For $9.95....I'll tell you

Hobart HL200C... | Answered on Dec 11, 2008 | 450 views


Contact Hobart directly to inquire.

Hobart Food... | Answered on Oct 31, 2019 | 38 views


Try this.

Take two flat blade screwdrivers and slip the blades between the planetary and the mixer body (on opposite sides) pry it off.

This has worked for me.

Hobart Food... | Answered on Oct 26, 2019 | 46 views


Contact Hobart directly to inquire. You probably want a service manual.

Hobart Food... | Answered on Aug 29, 2019 | 61 views


you need professional service. The gearboxes are full of grease and not nice to work on. Cogs have shear pins.

Hobart Food... | Answered on Jun 19, 2019 | 77 views


It sounds like either a partly stripped gear or a broken driving pin. If it is one of those options though I'm surprised it has not stopped completely.

Hobart Food... | Answered on Jun 17, 2019 | 67 views


one of two issues:
-either it has started pulling more amps than needed after many years of faithful service, or
-you now have something else plugged into the same circuit that is causing the circuit to trip

in either case, you will need an electrician to inspect and verify with multimeter (unless you know how to do so yourself). try unplugging any new items you may have purchased since just before the issues started

Hobart Food... | Answered on Jun 10, 2019 | 76 views


There is a shear pin in the gear in the gearbox head which shears when it is overloaded.. You need professional service.

It MAY be the 4th item on this page

https://www.partstown.com/hobart/d300/parts?page=0

Full parts schematic

http://www.hobart.co.kr/data_file/3D300Q794.pdf

Hobart Food... | Answered on May 03, 2019 | 75 views


Try a Commercial Kitchen equipment repairer or supplier. They may have what you are chasing.

Hobart Food... | Answered on Apr 10, 2019 | 85 views


FROM FIXYA
"Just give Hobart a call, and they should be able to help you (if you're in warranty, sometimes even for free!). Their phone number (according to their website, www.hobartcorp.com ) is 1-888-4HOBART (1-888-446-2278) "------

Hobart Food... | Answered on Apr 01, 2019 | 94 views


YOUR GUESS IS AS GOOD AS OURS WOULD BE . THO THEY DO MAKE A SILICON GREASE THAT IS USED IN THE FOOD INDUSTRY

Hobart Food... | Answered on Mar 08, 2019 | 133 views


Can you locate the motor?

See parts manual at link below. It doesn't show exactly where the cap is mounted but you should be able to follow leads from the motor to capacitor.

https://www.google.com/url?sa=t&source=web&rct=j&url=http://www.hobart.co.kr/data_file/3D300Q794.pdf&ved=2ahUKEwjS282GguvfAhUL4YMKHctCDJ8QFjABegQIAxAB&usg=AOvVaw1jczTOGy4VQ3CtATMnJEQZ

Hobart Food... | Answered on Jan 13, 2019 | 132 views

Not finding what you are looking for?
Hobart HL200C Mixer Logo

9 questions posted

Ask a Question

Usually answered in minutes!

Top Hobart Food Mixers Experts

Ross Keen

Level 3 Expert

1363 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Bruce Showalter

Level 2 Expert

133 Answers

Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...