Whirlpool RBD305PD Electric Double Oven - Page 2 - Answered Questions & Fixed issues

Okay this doesn't make sense did the breaker trip if so look for a short to ground I have serviced many of wall ovens in self clean the TOD does trip do you have a display if not the thermal cavity fuse is open if it stopped in self clean the door is locked as a tech I went to the auto store and bought some feeler gauges use one at the top of the door in the middle slide gauge between door and body push to the left to release the catch door should open

Whirlpool... | Answered on Sep 28, 2014 | 113 views

Hello there.
From the manual I got

To Stop Self-Clean any time:
temperature is too high, the door will remain locked. It will not
unlock until the oven cools

Hope it helps/

Whirlpool... | Answered on Sep 23, 2014 | 231 views

You need to remove the inner door panel, Usually a few screws holding it on. On some models the handle screws also need to be removed. Do it slowly and carefully as the door may want to swing up quickly, once the weight on it is removed. Pay close attention to each step so all screws etc go back in the same place. Make a diagram as you take them out to be sure.

Whirlpool... | Answered on Aug 11, 2014 | 349 views

First thing is to reset the breaker, it's tripped right now, so turn it on then off again then back on. If it kicks right back off again leave it off as you have a dead short and that can be dangerous especially with an electric oven. In that case call an appliance repair person.

If the breaker stays on after you reset it go back to your oven and see if it has come back on and is working. If it has power but the display is flashing some error code you will need to troubleshoot with the owners manual or look online for a manual.

If the oven is only a few years old it should "reboot" itself when power is restored. Some models require that you manually reset them with some combination of buttons (that's where you need the manual).

I hope this helps.

Whirlpool... | Answered on Jul 30, 2014 | 72 views

remove the door and reassemble

Whirlpool... | Answered on Jul 26, 2014 | 72 views

this is how to replace door hinges

Whirlpool... | Answered on Apr 29, 2014 | 27 views

all of them. arnt these visual blow fuses? does the lil wire look broken? or r they all solid state?

Whirlpool... | Answered on Apr 13, 2014 | 30 views

It may be the self clean latch not closing or locking

Whirlpool... | Answered on Mar 02, 2014 | 208 views

Pull unit slightly out of wall remove display panel screws tilt panel enough to see wires going to control board let know if there is an inline fuse leading to the board reason I ask the schematic does not show this fuse going on memory if so take the best picture you can a submit I'll give you the part # they use 5 different fuses, there is a reason fuse blew did you recently do a self clean does the cooling fan operates this draws air across the electrical components

Whirlpool... | Answered on Feb 08, 2014 | 96 views

If is 6 months old call for warranty repair, turn off circuit breaker for a minute then repower this may clear it if not again call for warranty service

Whirlpool... | Answered on Jan 30, 2014 | 498 views

Start here

Whirlpool... | Answered on Dec 06, 2013 | 301 views

Control Panel has likely failed (circuit board). You can try removing the power wire from the back of the panel and then replug it back in to see if it resets the board, but Im sorry to say your likely going to have to remove and replace the control panel.

Whirlpool... | Answered on Dec 02, 2013 | 237 views

door switch/spring is defective or clogged with grease.

Whirlpool... | Answered on Nov 23, 2013 | 55 views

Pretty sure it's meant to.

Whirlpool... | Answered on Nov 22, 2013 | 119 views

These ovens require that you remove the whole side covering to get to the hinges and door hardware.

Whirlpool... | Answered on Oct 21, 2013 | 57 views

My oven lights work. The top oven stopped working and bottom oven was working and it stopped working now. And the control panel is blank and just beeps when the bottons are pressed. What should I check first?

Whirlpool... | Answered on May 27, 2015 | 198 views

Here is the fuse to order and it is located behind the control panel.

Whirlpool... | Answered on Jun 29, 2013 | 83 views

There is a thermal fuse at the connection for the control board.

Had the same problem. I repaired the board myself and ordered a replacement from sears parts direct. It is a repaired board not a new one but has the same warranty. You can get this board a lot faster. Here is the link. http://www.searspartsdirect.com/partsdirect/part-number/8302319R/0022/664. If you would like to repair your own board leave a post and I will help you.

Whirlpool... | Answered on May 11, 2013 | 378 views

my oven panel board say's E1 F2 what do I do

Whirlpool... | Answered on Mar 16, 2013 | 239 views

I had a very similar problem (I was observing the error & fault code "E6 F2", but not always.  I did always have the beeps.) on a Whirlpool RBD305PDS14 double oven built-in.  I spent time today (Oct. 21) and traced the problem down to the keypad flexible cable that connects the keypad to the oven control panel.


I cleaned the flexible cable contacts that seat into the board mounted female connector on the control panel board using a Q tip and isoproply alcohol.  This did the trick. 

(Elsewhere in this forum, there is information on how to remove the oven control panel and gain access to the control assembly.  I posted this information - keywords in subject: Whirlpool RBD305PDS14.)

Whirlpool... | Answered on Nov 16, 2013 | 2,033 views

Not finding what you are looking for?
Whirlpool RBD305PD Electric Double Oven Logo

409 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Ovens Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Cindy Wells

Level 3 Expert

6048 Answers


Level 3 Expert

85216 Answers

Are you a Whirlpool Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides