Whirlpool RBD305PD Electric Double Oven - Page 3 - Answered Questions & Fixed issues

I wrote a blog on this topic recently, perhaps this will help you:


Best Regards,

Whirlpool... | Answered on May 27, 2015 | 1,592 views

A lot of people seem to have ran into this problem. I had no luck finding a solution to this problem anywhere on the internet. I finally fixed this problem by replacing the control board. Wanted to put this info out here for others. The part swaps out fairly easy for all of you considering the fix yourself. Sears direct had the cheapest price.

Whirlpool... | Answered on Dec 24, 2012 | 818 views

You will need to replace the control board. Here is the part to order.

The part comes with a 365 day, any part, any reason return policy.

Whirlpool... | Answered on Nov 21, 2012 | 1,019 views

1. You need to pull the oven out a few inches to be able to access two screws on each side of the control panel. On my oven, I needed to open the lower oven and remove a screw from each side to allow a vertical cover piece to be removed. With those pieces removed, there were two screws on each side that went into the wood frame around the oven. I also had a screw on the bottom of the oven, but it didn't not look standard. With those screws removed, the oven pulled out fairly easy. Just need to pull out far enough so that the two screws on the control panel assembly are accessible.
2. Remove those two screws and the panel can slide out once a number of cables have been removed. I took a picture of the connections before removing so I was sure I would put them back correctly (see below). The ribbon cable comes off by raising the plastic piece on top of the connector.

I replaced my panel with a Sears part that had been rebuilt. I couldn't find any new parts anywhere. It's been three weeks and, so far, my oven is working fine.

Whirlpool... | Answered on Nov 04, 2012 | 2,572 views

I have a whirlpool double oven model number have a whirlpool double oven model number RBD305PD810 the display panel turns off and displays E2 F6and sometimes it doesn't turn back on. Which prevents me from cooking the display panel turns off and displays E2 F6 and sometimes it doesn't turn back on. Which prevents me from cooking

Whirlpool... | Answered on May 27, 2015 | 364 views

The control panel part on my Whirlpool double oven (part #8302319) went blank six months back. Replaced it. Asked if there was a warranty on the part, was told no there was not. Yesterday, the six month old control panel went blank. Disappointed that Whirlpool manufactures such garbage.

Whirlpool... | Answered on May 31, 2015 | 4,720 views

change the motor

Whirlpool... | Answered on May 10, 2012 | 71 views

All the information for that is usually located on the tag where the model and serial number are at. Electrical specs are 220v a/c 60hz. I can't recall the amperage. If you don't have the owners manual you can go to www.apdepot.com and get one

If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_4570d45317834dd3

Whirlpool... | Answered on Apr 27, 2012 | 1,294 views

Check for correct voltage at plug, in the mean time the oven will be disconnected from any power, see if it resets with no power for 10 minutes

Whirlpool... | Answered on Apr 14, 2012 | 566 views

try pressing ctrl-alt-del

Whirlpool... | Answered on Feb 19, 2012 | 246 views

There is a couple of things that could cause this. This oven has a cooling fan that is supposed to keep the electronics from overheating. There is a thermo cut-off that is supposed to shut it down if this happens.
If it worked like it should, all you have to do is replace the thermo cut-off and possibly the fan. If it didn't the control board will also have to be replaced.

Whirlpool... | Answered on Nov 20, 2013 | 382 views

Had the same problem. I repaired the board myself and ordered a replacement from sears parts direct. It is a repaired board not a new one but has the same warranty. You can get this board a lot faster. Here is the link. http://www.searspartsdirect.com/partsdirect/part-number/8302319R/0022/664. If you would like to repair your own board leave a post and I will help you.

Whirlpool... | Answered on Nov 29, 2012 | 607 views

I'll tell you how I fixed it with the low price of $19.99.

Whirlpool... | Answered on Dec 12, 2011 | 1,250 views

The fuse could be blown in the oven control wiring IF the temp inside exceeded that of recommended temps usually if the oven was in self clean and the temps exceeded that of which the bullet fuse is rated fer. themobilian_3124.jpg

Service Manual

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Whirlpool... | Answered on Nov 01, 2011 | 108 views

Hello & Welcome to FixYa
F01 error in your whirlpool double oven means a bad electronic control board that needs replacement. Please get back if your need more help.

Whirlpool... | Answered on Oct 25, 2011 | 742 views

I have the same problem with the same part and was told by AppliancePartPros that the Control Panel would not be available to them until Feb 2012. I noticed a discoloration near a power transister and the big power resister next door (installed with about a 1/2 inch clearance to the PCB board, labeled R188 on my REV A board). The solder connections from the R188 resister to the PCB were cracked. That resister was hot when I touched it and the thermal cycling probably cracked the solder joints after 9 years. I am going to resolder those connections tomorrow and see if that resolves the problem. Do you see any burn marks near that Power transister (3 lead black package with a metal heat sink on its back (the heat sink has a circular hole above the black plastic package)?

Whirlpool... | Answered on Oct 13, 2011 | 604 views

power failure

Whirlpool... | Answered on Sep 21, 2011 | 86 views

To Set a Cook T ime:
1. On double oven models only, press UPPER OVEN or LOWER
OVEN for the one you want to set.
2. Press BAKE or CONVECT UPPER (on some models).
Press the number pads to enter a temperature other than the
one displayed.
3. Press COOK TIME.
4. Press the HR and MIN "up" or "down" arrow pads to enter
the length of time to cook.
The start time and stop time countdown will appear on the
oven display.
On double oven models only, when both upper and lower
ovens are being used at the same time, touch UPPER OVEN
or LOWER OVEN to display the respective cook time.
When the stop time is reached, the oven will shut off
automatically and "End" will appear on the oven display.
If enabled, end-of-cycle tones will sound, then reminder
tones will sound every minute.
Repeat the process by choosing the other option of UPPER or LOWER OVEN

Whirlpool... | Answered on Sep 04, 2011 | 124 views

Try turning off the circuit breaker to the oven for 30 min or so and then turn it back on. If it does not come back on the oven probably got a power surge and the control has been damaged. Hope that helps

Whirlpool... | Answered on Aug 30, 2011 | 74 views


The E6-F2 error code means that the control board thinks there is a problem with the cancel button on the touch pad. Sometimes its due to a loose connection from the ribbon cable on the touch pad. You can push cancel and clear it and if within 5 or under the error code returns the touchpad needs to be replaced. But first check/have the connection checked to make sure its tight. The way modern things work though is grand and Whirlpool say if after replacing touchpad the error code returns once again the clock/control board is what needs to be replaced.


Whirlpool... | Answered on Mar 20, 2013 | 564 views

Not finding what you are looking for?
Whirlpool RBD305PD Electric Double Oven Logo

409 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Ovens Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Cindy Wells

Level 3 Expert

6048 Answers


Level 3 Expert

85216 Answers

Are you a Whirlpool Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides