Whirlpool RBD305PD Electric Double Oven - Page 4 - Answered Questions & Fixed issues


A small fuse is mounted in line with the power going into the control.
themobilian_2806.jpg

Service manual Page 22


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Whirlpool... | Answered on Aug 11, 2011 | 485 views


Hi did the fuse or breaker tripped off fora while..Check as well the thermostat by opening the back cover of the oven..there are several reason thermostat might not be working for the upper element.They are responsible of adjusting temperature.Using a tester yuo can check the continuity of the temperature control or the temperature control need to be calibrated.or somehow controls had been busted..Selector switch might as well been busted ..

Whirlpool... | Answered on Jul 07, 2011 | 62 views


you can order this part from repair clinic.com.At present this part is out of stock. ------------ click this link below:--
http://www.repairclinic.com/PartDetail/Touchpad/4451314/589799 ----------- They also mostly all types of control touch pad board. --------- This is there contact details.Just contact and get the exact detail for when the part will be in stock.also they have all types of board.Confirm if they have any compatible, or substitute board available.------ 1-800-269-2609/ open 7 days.Timing morning 7 to evening 8.
  • -----------
  • -------This should help.Keep updated.Thanks.Helpmech.

  • Whirlpool... | Answered on Jun 16, 2011 | 482 views


    Hello, Thank You for using FixYa. I will be helping you today.I would recommend paying for a service call to have a tech take the door apart for you. There are four pieces of glass in the door and lots of screws. It really is a pain to take doors apart we as techs get this call all the time. Believe me you will thank me you paid someone to do it. If it were easy i would tell you. Most people take them apart then end up paying because they cant put it back together.
    Thank You and please rate my answer if it was helpful..

    Whirlpool... | Answered on Jun 10, 2011 | 535 views


    See page 22

    If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

    Whirlpool... | Answered on Jun 02, 2011 | 40 views


    Hello mjama,

    I understand that you are having a problem with your cook top sparking after cleaning. If you are talking about your burner/element sparking this is usually the case when the element is fixing to go out and needs to be replaced. However, if this is not what you are talking about please post make and model of your cook top and what is sparking.

    Thank you for choosing FixYa.com

    Justin

    Whirlpool... | Answered on May 08, 2011 | 63 views


    Ovens run on a 220 Volt circuit. That is two 110 Volt wires in reality, one from each side of the main. If one line is tripped only part of the oven will work. Check the Main for a tripped circuit. The range breaker should have a metal bar or pin connecting both halves of the breaker. If not it can trip on one side only. If you installed the "pig tail" yourself, turn off the main oven breaker and double check your connections. Black on each side (one may be red) and white wire in the middle. Neutral ground wire to metal plate of fixture.

    If the power connections are correct and your panel still does not work it will probably need replacing. Do not open the access panel if it is under warranty (breaking a warranty seal will void the warranty) or you are not qualified to work on the wiring. It is better to call a tech without opening it. If you have opened it and then call a tech it will probably cost much more to fix as they will have to check ALL the circuits to be sure you have not damaged it.

    Since it is a wall mounted unit be sure to check the wire for adequate slack and that it does not get crushed when the oven is installed. Metal Flex conduit is recommended (and may required in your area) between the wall supply box and the oven to protect the wire from shorting or damage.

    Caution - 220 Volts can easily kill a person.

    Whirlpool... | Answered on Apr 13, 2011 | 120 views


    Probably your heating element has failed, dependant on appliance the element can be found in the oven itself at the back behind a panel that normally has a couple of screws holding the panel in place. reasonably easy to fit yourself and not very costly.

    Hope this helps

    Whirlpool... | Answered on Apr 13, 2011 | 415 views


    Hello & Welcome to FixYa

    Error code F1 is displayed due to electronic oven control failure and the only way to solve this problem is by replacing the control board which is bad. Sorry for the bad news but hope you understand... Please get back to me if you have any other questions.


    Kevin

    Whirlpool... | Answered on Apr 11, 2011 | 171 views


    you can run it at 350 for like a half hour or so and you'll smell a funny smell from the metal heating up,when i replace an ignitor or an element i run it for like 10 minutes just to burn off the smell of the metal.i'm sure the factory already had that fired up to check it but i would start it and burn anything off of it that might be in there before i cooked anything,it can't hurt it.good luck with your new machine.

    Whirlpool... | Answered on Apr 08, 2011 | 88 views


    Hi Pwaldo,

    If you're experiencing error E6 F2 it might caused by faulty control board or control panel. Here are some ways to check this error, you can just assemble the control panel back or just unplug and replug the keypad ribbon. You could also try to do the following steps below for additional troubleshooting.

    1. Disconnect the Oven from the power outlet ( remove the power from the oven ).

    2. Please open the control panel then unplug the key pad ribbon from the control board.

    3. Now assemble the control panel back then plug the oven to the power outlet then try powering it on.
    --> please wait for few hours and observe the machine.

    4. If you still have the same problem like the error E6 F2, you need to replace the control board.
    - you may try to search on this part number for the control board AP3595759.

    --> If you noticed that error did not show up, you need to replace the control panel ( the keypad comes as a control panel assembly ).
    - please try to search for this part number for the control panel AP3131755.

    - you may also contact the manufacturer to consult the part numbers.

    Hope it may helps.

    Thank you for using FixYa.

    Whirlpool... | Answered on Apr 02, 2011 | 163 views


    REPLACE CLOCK UNIT ...... BSC APPLIANCES 07779933829 UK

    Whirlpool... | Answered on Feb 25, 2011 | 71 views


    F2 E6 means the cancel key drive is open.
    1. Check keypad connector for firm connection (keypad connects to control board).
    2. Press CANCEL. If error code returns after 60 seconds, replace keypad (also called touch pad or membrane switch). Some models incorporate keypad in to control board as one unit. In this case, replace control board (also called ERC or clock).

    Whirlpool... | Answered on May 31, 2015 | 220 views


    F3 means that the oven temperature sensor has a open circuit. Check connection from sensor to the control board. If connection is good, replace oven temperature sensor. Hopefully the wires are long enough, then you can unscrew oven sensor and pull the connector thru hole to check connection and to replace. If its not long enough, you will have to remove oven from wall to check

    Whirlpool... | Answered on Feb 13, 2011 | 299 views


    We fix this problem frequently, here's a short article about it:

    http://www.fixyourboard.com/techzone/ovens/e6_f2/e6_f2.html

    Whirlpool... | Answered on Jan 29, 2011 | 135 views


    Up there in the controls is a bullet fuse like this:
    themobilian_1084.jpg
    Designed to kill power to the controls if it gets too hot in there so the controls won't be harmed. That could be it but I don't know if it would beep if the fuse is blown, that could be a bad control. Use this manual to help you diagnose:

    Whirlpool double oven repair manual

    If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

    Whirlpool... | Answered on Jan 26, 2011 | 603 views


    Remove the power from the oven. Open the control panel and unplug the key pad ribbon from the control board. Assemble the control panel back and turn the power on. Wait a few hours.
    If the error code came back on, replace the control board.
    If the error code did not show up, replace the control panel
    Oven repair in Mission Viejo, CA
    Appliance repair in Mission Viejo and Orange County, CA

    Whirlpool... | Answered on May 27, 2015 | 694 views


    This is a frequently occurring problem due to a failure in the control board. The board can be repaired to solve this.

    http://www.fixyourboard.com/techzone/ovens/e6_f2/e6_f2.html

    Whirlpool... | Answered on May 27, 2015 | 287 views


    You will need to replace the control board. Here is a link to the part.

    Whirlpool... | Answered on Jan 21, 2011 | 630 views


    FIRST THING IS CHECK YOUR BREAKER TO MAKE SURE YOU ARE GETTING A FULL 220 VOLTS,,,, THEN TAKE THE UNIT OUT OF THE WALL AND CHECK THE VOLTS WHERE THE WIRES HOOK ON THE TERMINAL BLOCK,,( MAKE SURE THE POWER IS OFF WHILE YOU TAKE THE UNIT OUT, THEN WHEN IT IS OUT AND YOU MAKE SURE THE WIRES ARE NOT PULLED REAL TIGHT, THEN TAKE THE PANEL OFF TO GET TO THE TERMINAL BLOCK, THEN TURN THE POWER BACK ON TO CHECK THE VOLTS),, IF YOU ARE GETTING THE FULL 220 VOLTS THEN IT IS LIKLEY THE TOUCH PAD HAS WENT OUT,, I HAVE SEEN ALOT OF THESE BUT MOST WERE JUST NOT GEETING ENOUGHT POWER,, IT RUNS ON 220 VOLTS 110 TO POWER THE ELEMNTS AND LIGHT AND 110 TO POWER THE ELECTRONICS

    Whirlpool... | Answered on Jan 19, 2011 | 60 views

    Not finding what you are looking for?
    Whirlpool RBD305PD Electric Double Oven Logo

    409 questions posted

    Ask a Question

    Usually answered in minutes!

    Top Whirlpool Ovens Experts

    John Tripp
    John Tripp

    Level 3 Expert

    4656 Answers

    Cindy Wells

    Level 3 Expert

    6048 Answers

    Marvin
    Marvin

    Level 3 Expert

    85216 Answers

    Are you a Whirlpool Oven Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...