Whirlpool RBD305PD Electric Double Oven - Page 5 - Answered Questions & Fixed issues


F2 and e6 in combination indicate a cancel key open condition. What this means in layman's terms is that the key-panel Has a problem. If it was just recently cleaned with a wet cleaner, you can try drying the keypad off or even CAREFULLY warming it up with a hair dryer. Don't get it too hot so that you melt anything.
If this does not work, you will need to replace the key panel on the oven.
You can do this repair yourself and should you decide to, please just comment back with the full model number off the tag on the oven and I will give you step by step instructions on how to do it.
Good luck!!

Whirlpool... | Answered on Nov 03, 2012 | 759 views


it could be the following
Taking a Quick Look
The E1 F2 error message indicates the control board thinks the touch panel has been unplugged from the board or it cannot read the switches.
How it Works
The panels on these ovens utilizes a switching matrix to constantly monitor all the buttons for a key press. By using a matrix for switch input, many buttons can be read by the processor using very few wires. The unfortunate side of a switch matrix is if any one wire becomes damaged, an entire row of switches on the matrix will no longer be usable since they cannot be seen by the control board.

advise
getting a qualified engineer to check this touch panel and suspect touch panel maybe defective and need replacing.

I hope this was helpful

Whirlpool... | Answered on Jan 05, 2011 | 203 views


I think Whirlpool and Jen Air use the same display board, It's worth a check anyway.

BrianGem posted a great solution back in May of '08, I just completed that fix on my own Jenn air, took me about 30 minutes once I got the correct capacitor.
The display board apparently has a weak spot in the
design, most likely heat related, (probably low priced components from offshore sources)
Fix: Replace heat damaged capacitor labeled C3 on display board, Hard part will be obtaining the 35Volt 68uF capacitor, I'm lucky enough to have a Brother in the electronics design field who found me a couple of high reliability caps designed for hot applications, He does not recommend changing sizes without design review for fear of overloading another component, however several other posts have indicated that a 35V 100mF cap has worked fine for them.

TURN OFF POWER TO OVEN PRIOR TO STARTING ANY REPAIRS.
My control panel was attached to the oven with 4 screws accessed from above the top oven door, the panel slid up about 1/2 " and lifted off, Unplug the ribbon cables and the panel can be removed to a convenient work surface. The display board itself is mounted with 4 screws and connected with a wide flat ribbon cable, the suspect capacitor is surface mounted to the reverse side of the board, two plastic clips need to be released (gently) and the ribbon cable unplugged. Capacitor is likely discolored or leaking, Using as small a soldering iron as you can find De-solder it and replace with new, match polarity marks and don’t use any more solder than needed.
If you run into trouble drop me an e-mail to dltatsjc@aol.com and I’ll try to help.
Good luck.
Thanks for this site..

Whirlpool... | Answered on Jan 04, 2011 | 1,017 views


Probably blew a fuse after overheating in the control compartment. Look for one of these fuses going in to the control
themobilian_507.jpg

I have your Oven Service Manual here that shows how to access the innards of that control and also diagnose the problem HERE

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Whirlpool... | Answered on Dec 20, 2010 | 135 views


You have most likely caused one or more fuse relays to blow.
The self-clean operation can not be interrupted before the cycle is complete without causing issues.
There is the main fuse inside the control panel and 2 fuse relays on rear of the oven.
In order to access these fuses you must open the door,then remove the mounting screws to remove the oven from its cabinet..
Use a wire coat hanger bent into a "U" shape on one end.
The door latch is in the center of the door on the top oven.
Slide the bent wire coat hanger between the door and the oven opening.
The "U" of the coat hanger will be right center of the door latch.
Slowly pull the "U" to the left until it catches the latch.
Then pull steady and forcefully to pull the latch mechanism to the left while putting pressure on the door to open it.
Once the door is open you can begin to access the parts for diagnosis and repair.

Whirlpool... | Answered on Nov 28, 2010 | 79 views


Hello,

The glass door of an oven, it to protect the heart generated from the heater that i.e the element snd also protect food during and after cooking from jams and bacterial penetrate going to the food and also protect children from putting there hard in the oven.

However, it first function is to protect the heat generated by heat provider (element)
the internal glass of an oven is more stronger then the external glass if you make use of the oven with out the internal glass the room is at high risk! why? because the external glass does not have the strength to with hold the heat generated by the element.

PLEASE NOTE:Do not make use of the oven with out the internal glass no matter the level of the how urgent you want to make use of the oven remember SAFETY FIRST.

Thank you and thanks for using fixya.

Whirlpool... | Answered on Nov 27, 2010 | 209 views


Can't bypass the sensor. sounds like it may be the control

Whirlpool... | Answered on Nov 23, 2010 | 63 views


i also need one asap

Whirlpool... | Answered on Dec 16, 2010 | 982 views


Hi and welcome to FixYa, I am Kelly

The error & fault code "E6 F2" is a keypad or keypad connector problem. However... the control board can also cause this fault. Sometimes you can clean the ribbon and connector at the control board attachment point and correct this.

There is a tech sheet inside the control panel (envelope) that has all of the error codes listed.

The control boad has a female connector with 2 release tabs for the ribbon. YOU MUST unlock the release tabs to remove the ribbon. This is a tedious process but if your gentle and take your time you can coax the ribbon out of the connector. The contact area of the ribbon is quite thin. I have found that you can place something non metalic and FLAT behind the ribbon and then use a tissue to gently clean the ribbon wiping in the same direction of the electrical runs on the ribbon. I.e. wipe from above the bitter end down to the bitter end. (one direction only) The female connector on the control board is much more forgiving. Once you complete the cleaning process press the ribbon back into the female connector and lock the 2 tabs.

If this does not correct the problem you can end up changing the control board (1st) and the touch pad (2nd) to fix it.

If you need help with locating parts just respond here and I will gladly assist you.

Thanks for choosing FixYa,
Kelly

Whirlpool... | Answered on Sep 19, 2011 | 234 views


sounds like it is the wrong one pretty common problem with those control panels

Whirlpool... | Answered on Nov 19, 2010 | 170 views


The thermal switch is located behind the control panel. In order to access remove the control panel. It should be located inside the aperture.

If you have any further questions please feel free to ask.

Whirlpool... | Answered on Nov 17, 2010 | 336 views


The following link explains step-by-step how to replace the control panel on most kitchen ranges:

http://www.fixya.com/support/r3727366-replacing_control_kitchen_range


You can also refer to searspartsdirect.com, pcappliancerepair.com, or appliancepartspros.com for helpful exploded view parts illustrations that will assist you with any repairs you may need to perform.

If you have any questions about this repair, please post back and let me know. I hope this helps you.

Whirlpool... | Answered on Nov 06, 2010 | 149 views


F2 - E6 Cancel key drive line open 1. Check keypad connector for firm connection (keypad connects to control board).
2. Press CANCEL. If error code returns after 60 seconds, replace keypad (also called touch pad or membrane switch). Some models incorporate keypad in to control board as one unit. In this case, replace control board (also called ERC or clock).

Whirlpool... | Answered on Mar 20, 2013 | 1,011 views


HI. This code is in reference to the control sector. There seems to be a malfunction that has been detected within the touch/key pad assembly. Use the procedure to isolate the damage.


1. Check keypad connector for firm connection (keypad connects to control board).

2. Press CANCEL. If error code returns after 60 seconds, replace keypad (also called touch pad or membrane switch). Some models incorporate keypad in to control board as one unit. In this case, replace control board (also called ERC or clock).

Whirlpool... | Answered on Nov 03, 2010 | 371 views


HI, this is referring to the cancel key on your key pad. It is stuck open. follow the procedure below.

1. Check keypad connector for firm connection (keypad connects to control board).

2. Press CANCEL. If error code returns after 60 seconds, replace keypad (also called touch pad or membrane switch). Some models incorporate keypad in to control board as one unit. In this case, replace control board (also called ERC or clock).

Whirlpool... | Answered on Mar 20, 2013 | 425 views


WHEN MY OVEN KEPT BEEPING AND LATER IT WOULD NOT OPERATE, I CALLED THE LOCAL COMPANY WHO SOLD MT THE OVEN...(KITCHEN CONCEPTS), THEY FORWARDED ME TO THEIR SERVICE COMPANY WHO CAME OUT AND LOOKED AT THE ERROR CODES AND SAID, "THERE IS NOTHING BUT BAD NEWS) THE CIRCUITS IN THE OPERATING CIRCUITS HAVE BEEN BLOWN OUT BY SURGES...IT WILL COST $538 TO REPLACE THEM....HIS STORY WAS THAT IN OUR NEIGHBORHOOD, THERE ARE A MULTITUDE OF SURGES...MY QUESTION IS WHY THE HELL DOES WHIRLPOOL PUT OUT A $1100 OVEN WITH NO PROTECTION FOR SURGES....CHECKING ON THE NET, I SAW MANY BAD FEATUIRES ON MY OVEN....DON'T USE THE OVEN CLEANER AS IT WILL COOK YOUR CIRCUIT BOARDS AND SEVERAL OTHER....WHAT A PIECE OF ****....I AM GOING TO WRITE THE COMPANY AND *****....TO NO AVAIL, THANK YOU FOR YOUR HELP....

Whirlpool... | Answered on Nov 01, 2010 | 491 views


Yes, at www.fixyourboard.com , we repair this controller frequently. An E6 F2 error code on these parts has always been due to the control board. These controllers can be repaired quickly and reliably for a fraction the cost of a new one. If buttons are not working or you get an F2-E0 or F2-E1 then it is the keypad. T

Whirlpool... | Answered on Apr 24, 2015 | 2,970 views


The E1- F5 error is a door lock error.

The control (TIMER) has likely failed in this instance - BUT...

Sometimes when you disconnect power to a range and reconnect it the electronic range control gets confused.
You should disconnect power again for 15 seconds and reconnect and see if that helps.

If it doesn't cure the E1- F5 error hold the bake button in until E0- F2 appears in the display.
This is the error for a stuck button on the keypad and is the way to clear the memory of the electronic range control.

Sometimes these work, but if the control has failed it won't make any difference.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.^&^TG

Whirlpool... | Answered on Oct 01, 2010 | 144 views


F2-E1 - Touch Pad (Keypad) Cable Unplugged -
Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure.
Select the 'cancel' function and wait 60 seconds.
If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.

It appears your timer/clock has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.&&&&&&&&&&&&&&&

Whirlpool... | Answered on Oct 01, 2010 | 913 views


F2-E1 - Touch Pad (Keypad) Cable Unplugged -
Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure.
Select the 'cancel' function and wait 60 seconds.
If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.

It appears your timer/clock has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.!!!!!

Whirlpool... | Answered on Oct 27, 2010 | 196 views

Not finding what you are looking for?
Whirlpool RBD305PD Electric Double Oven Logo

409 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Ovens Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Cindy Wells

Level 3 Expert

6049 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a Whirlpool Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...