Whirlpool RBD305PD Electric Double Oven - Page 8 - Answered Questions & Fixed issues

Whirlpool RBD305DQ15 Electric double wall oven, the control panel does not light up so you can't tell what you are doing. Do I need to replace the whole board or is there a fuse to replace?

Whirlpool... | Answered on Oct 10, 2009 | 615 views

If you can email me the full model number I can dig up the exploded parts diagram and maybe a link to the service manual for you. I don't know if can can post the image on this site, but I can email it to you.


Whirlpool... | Answered on Sep 22, 2009 | 723 views

try turning power off and wait 10mins and see if it resets.

Whirlpool... | Answered on Sep 14, 2009 | 711 views

No,but it can be calibrated through the control push and hold the Bake button it should come up 0 F you can go plus or minus 35 degrees with the up and down keys.but make sure your thermometer is accurate.Whirlpool will send someone out to check it out for free for the first year.

Whirlpool... | Answered on Sep 02, 2009 | 199 views

the humming sound is coming from the "squirrel cage" fan in the back of the unit, there may be some resonance vibration from the fan this issue should be addressed by a qualified service tech, the whole wall oven needs to be pulled out, i would have him check the fan.

Whirlpool... | Answered on Aug 27, 2009 | 937 views

When you self clean your oven, it heats to over 800 degrees. This usually takes out one or more electronic parts. I recommend that you purchase the part yourself and install it to save you a lot of money. Then, don't self clean it any more. I recommend that you wipe out the oven as often as you can and try to NEVER use the sefl clean option. Call us for parts at 972-859-0929. The same part is most likely out this year that was out last year. Hope this answers your questions! Ella

Whirlpool... | Answered on Aug 26, 2009 | 130 views

HI, this is a faulty key pad issue. check the following.

1. Check keypad connector for firm connection (keypad connects to control board).
2. Press CANCEL. If error code returns after 60 seconds, replace keypad (also called touch pad or membrane switch). Some models incorporate keypad in to control board as one unit. In this case, replace control board (also called ERC or clock).

Whirlpool... | Answered on Nov 29, 2013 | 366 views

might be a bad temp sensor

Whirlpool... | Answered on Jul 30, 2009 | 551 views

Is the clock re-setting and flashing? Either the fan is failing and the oven is overheating, or the thermostat is faulty and the oven THINKS it is overheating. It is a fail-safe kicking in, momentarily cutting power to the oven to avoid lasting damage.
Set the time on the clock and the oven should be okay to go again, but if problem repeats, replace the fan and/or the thermostat - it is difficult even for an engineer with all his equipment to diagnose which of the two is at fault, but its about all there is to go wrong on a gas oven.

Whirlpool... | Answered on Jul 20, 2009 | 557 views

Oven temperature sensor (RTD) open

Replace Oven temperature sensor (RTD)

Whirlpool... | Answered on Jul 11, 2009 | 171 views

probaly blown thermal fuse replace thermal fuse\

Whirlpool... | Answered on Jun 27, 2009 | 274 views

control board is bad, contact sears to ix

Whirlpool... | Answered on Jun 14, 2009 | 178 views

Please take a look at the diagram if you think you want to do that.
if you still want to do it and need more details to disassemble feel free to email me. nguyen@ite.net


Whirlpool... | Answered on Jun 09, 2009 | 412 views

HI, you will need to replace this faulty ECC. the chip set that is soldered on this board is damaged as well as the led display. replacing the Electronic Clock Control will fix this issue.

the control board is fine and this explains why the oven is still functional. its the ECC that is faulty.

Click here to purchase your new ECC online.

Whirlpool... | Answered on May 26, 2009 | 709 views


Whirlpool... | Answered on May 28, 2009 | 1,510 views

Usually this is a touchpad and control panel fault but the only way to know for sure is to do some electrical testing with a volt/ohm meter and the wiring diagram located within the appliance.

With the model number of the oven we could look up the code and be more specific about the problem.

Go here for: http://www.repairclinic.com/Whirlpool-Range-Stove-Oven-Parts


appliance parts, help & more

Whirlpool... | Answered on Apr 09, 2009 | 1,037 views

All manuals for Whirlpool RBD305PD are here.

Whirlpool... | Answered on Apr 06, 2009 | 1,004 views

The control panel may have a power issue. Replacing the board fixed my problem. It looks like 4 resistors and a ZD1 diode heat up and fail. The U1 chip could also be a problem. If you replace the controller it will cost around $225. Be careful of the key pad ribbon cable. They break easily. Another $186. Good luck.

Whirlpool... | Answered on Apr 01, 2009 | 485 views

The power is going out to the control panel. It is easy to replace the whole controller. Be careful of the key pad cable. it will break easily. The part is $225 for the controller and $172 for the key pad. There are 4 resisters that heat up and a zen diode that fails DZ1. U1 also may fail. My RBD306PDB10 works great now. Do pay attention to the cavity size after re-installing the board.

Whirlpool... | Answered on Apr 01, 2009 | 342 views

The only repair is to replace the ERC (clock).

Whirlpool... | Answered on Mar 30, 2009 | 375 views

Not finding what you are looking for?
Whirlpool RBD305PD Electric Double Oven Logo

409 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Ovens Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Cindy Wells

Level 3 Expert

6046 Answers


Level 3 Expert

85206 Answers

Are you a Whirlpool Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides