Whirlpool RBD305PD Electric Double Oven - Page 9 - Answered Questions & Fixed issues

true it may be afuse, but not just any fuse that yo ucan by at the hardware store, if your able t o remove th panel the "fuse" if applicable( some models dont use one) is an inline fusable link located at the end of one of the wire connectors, standing in front of unit the connector is located right midsway in control board, its usually with a bunch of wires and youll see a white wire "attached" to the fuse which to the eye is a small silver/blue metal sleeve. in orderto replace youll need to "poke" the wire out of harness and replace. chances are you also have a bad over temp thermostat which has gone bad as well and that s located on back wall of unit, requiring removingform the cabinet.

Whirlpool... | Answered on Mar 25, 2009 | 1,094 views

the element has probably blown.

Whirlpool... | Answered on Mar 13, 2009 | 169 views

oven does not light up, no heat

Whirlpool... | Answered on May 01, 2009 | 958 views

The fans are not normally repairable, but there is no problem obtaining replacements.
On a double oven, there are usually 2 fans fitted.
There is an external cooling fan usually fitted on the top of the oven, you would have to remove the top cover of oven to access it, and possibly the rear panel as well.
Then there is the fan fitted in the main oven compartment.
If you open the oven door as it is working, you should be able to determine if it is the fan oven or the external cooling fan that is the cause of the problem.
If you determine it is the fan in the oven that is noisy, then to undo the fan blade assy, you have unscrew the nut clockwise to remove it. as opposed to the normal way of undoing a nut.
Please rate my fixya solution.

Whirlpool... | Answered on Feb 09, 2009 | 1,723 views

try holding down clock button.. when you 1st hold it down it will appear.. keep holding til it disappear.. then when it comes back on let go of button.. if clock button don't try another like + or - sign.. good luck.. mike

Whirlpool... | Answered on Oct 03, 2012 | 583 views

Thanks Mike.
Yes it is the same.
Make sure that the timer is set to manual, and not on auto or the oven will not work..
It should tell you the procedure in your user instructions.
Plz rate my solution.

Whirlpool... | Answered on Jan 10, 2009 | 178 views

If it is only cracked and still otherwise intact (not shattered in bits) you are OK to cook the turkey. Just don't put it in self clean until you replace or have the glass replaced. Brian

Whirlpool... | Answered on Dec 21, 2008 | 135 views

the problem is the high voltage relay which might be on the control board or on the back of the oven . the contacts on the relay are most likely fused together check with a ohm meter.

Whirlpool... | Answered on Dec 12, 2008 | 97 views

This happened to us the first time we used the self-cleaning feature. The repairman said we had to replace the whole electronic panel -- but when he put in the new panel it didn't work either. It turned out he just needed to replace the oven shutdown thermal fuse I believe. We finally got up enough courage to try the self-cleaning again and the exact thing happened. The door is locked and the electronic panel is dead again. So when we get it fixed we will never use the self-clean again.

Whirlpool... | Answered on Jan 11, 2009 | 680 views

Unless your cooker is totally different to the norm, then yes you can use 3 core cable. assuming you are in the u/k, then the following applys.Brown is live-Blue is neutral, andGreen/Yellow is earth.
Depending on the total wattage of the cooker, you will need to use a min of 6mm twin and earth cable, If in any doubt, consult an electrician
Please leave feeedback

Whirlpool... | Answered on Dec 05, 2008 | 111 views

You will not be able to access a service manual on line.
You will have to go to Whirlpool web site and request one.
There will normally be charge for this

Whirlpool... | Answered on Dec 05, 2008 | 159 views

It is NOT safe to do this due to the water content of the steam when it condenses.

Better to use an aerosol type oven cleaner.

Whirlpool... | Answered on Dec 01, 2008 | 144 views

Probably have a thermal fuse out. Need a test meter to diagnose this, so you may want the reapir man. No point in buying a control if you don't really know what is wrong.... I cannot see your reply due to some tech issue w/ the site, so it may be a day or so before I can reply again. Please leave feedback for me if appropriate. Thanks

Whirlpool... | Answered on Dec 02, 2008 | 217 views

yes, but the unit will need to be pulled out. then, you can unscrew the back panel and attach the wire to the element. Joe

Whirlpool... | Answered on Nov 19, 2008 | 46 views

Hello hward,

You said, Hello from Baton Rouge, La. just recently nailed by Hurricane Gustav.......
during the hype of the storm, I think my wife's double oven took a electric surge and started smoking. I visually inspected the damage and saw a badly burnt and scarred flat saucer looking component (suppressor, transient)...I have ordered a replacement part and would like to know if you think that replacing this item will be all I will need to do..

If the range was under water I do not think this will be the only problem.
I believe it will cause you endless problems if it got submerged!
you may end up replacing this water logged unit!

Thank You ,Please remember to leave a rating

Whirlpool... | Answered on Oct 21, 2008 | 191 views

Hello kybattey
Welcome to Fixya.

You said, After coming on and preheating Saturday, the upper oven went off and the lower wouldn't work either. Control paned was blank, but interior lights were on and pushing control paned buttons resulted in beeps. Turned off breaker for 5 minutes to reset and upon retry, the fan came on for maybe 5 seconds and then went off. Nothing else changed. Any suggestions?

You say the ovens went on and then later cut off.
Does the clean mode work?
Try the clean mode and see if it goes on.
Assuming it will clean!

Since the Range will clean you have confirmation that the proper power is reaching the range. It also verifies that the elements are in working condition. You will need to check the high temperature limit switch and the door latch mechanism. If either of these is defective, the bake and broil function will not operate properly
Let me know how it goes.
Waiting your response.

Please remember to leave a rating when done!

Whirlpool... | Answered on Oct 21, 2008 | 270 views

Hello ssuebe51

Turn the power off to the oven.

Check the connection from the key pad to the clock.

If the connection is good then put back together.

Turn power back on and press the cancel button.

If the error code returns after 60 seconds then the keypad will have to be replaced.

Thank you huuum
Please remember to leave a rating

Whirlpool... | Answered on Mar 20, 2013 | 521 views

Hello raco1

I need your model number to look up the fault code !!!!
You said , you see fault codes, FD F3 and E2 F3 is showing up on display pane

Looks like this may be your problem
F3 - E2 - Oven to hot -Replace oven temperature sensor

Waiting for your response.
When responding send me this whole communication . Not just your answer!
Thank you Huuum.

Whirlpool... | Answered on Aug 14, 2012 | 1,156 views

i got a tech sheet for your range accept this message as a fix ya and e mail me at b4829@yahoo.com and ill send it back as an attachment just say f2 e6 code

Whirlpool... | Answered on Mar 20, 2013 | 524 views

Not finding what you are looking for?
Whirlpool RBD305PD Electric Double Oven Logo

409 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Ovens Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Cindy Wells

Level 3 Expert

6048 Answers


Level 3 Expert

85216 Answers

Are you a Whirlpool Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides