20 Most Recent Whirlpool GHW9100L Front Load Washer Questions & Answers

normally when one fault is generated after fixing another fault, it is normally down to something caused by the person working on it, this could sound like you have dismantled something on the suspension, you say you changed the pump, (did you tip it upside down to work on it) if you tipped it up to work on it check the suspension legs to make sure they look equal, as the chrome inner drum can not possibly be that far out of alignment, the whole drum unit can be though, thats a different matter, check suspension and get back to me,if i have helped rate me please

Whirlpool... | Answered on Nov 12, 2018

Locktite, TM, is an excellent choice, as long as the nut engages three full turns on the threads. alternatively, if there is sufficient thread to use two pal nuts tightened against each other. The biggest problem is that to hold the retaining nut, being thin, requires a thin wrench, while the locking nut can use a regular wrench. If there is enough thread on the shaft for teo pal nuts, the regular locking nut may not engage the locking insert, in which I would use the Locktite. Are you sure you didn't install a thrust washer on the wrong side of the bearing mount, possibly not even intended but worth checking,

Whirlpool... | Answered on Sep 09, 2017

The following link explains the "F05" error code:


I hope you find this information helpful. I have seen this error code generated by something as simple as a loose connector on the NTC sensor. Hopefully, you can resolve this with no expense. If you do require any parts, however, you can locate parts with illustrations at searspartsdirect.com or repairclinic.com. If you require further assistance, please let me know.

Whirlpool... | Answered on Mar 27, 2017

Two things I can think of , the coupling to the pump has broken or a coin or other object has entered the pump and jammed it. either way the pump will have to be removed for repairs.

Whirlpool... | Answered on Feb 05, 2016

Most noises from a washing machine occur during the rinse or spin cycle. If you hear loud thumping during the spin, the load of clothes may have become unbalanced. Stop the washer and redistribute the clothes, then re-start it. Repeat these steps if necessary.This will solve your problem.

Whirlpool... | Answered on Aug 28, 2015

1 close washer door and dispenser drawer
2 select Clean washer cycle
3 Press start/ pause
The basket will rotate,then the door will unlock,lock again,then the cycle will continue
Water should come in and run a short sensing cycle about 3 minutes
4 This will determine item in the washer
a if no items are detected it will move to step 5
b if item are detected wash any control lock light will stay on door will unlock open and remove any garments
If b pessnpower to cancel f code then repeat 1,2,3
Once cycle begins allow it to finish
5 after cycle is complete leave the door a jar to allow for venting and drying of interior
Only use HE high efficiency detergent

Whirlpool... | Answered on Jul 18, 2015

The agitator -- the finned part that fits on the tub shaft -- can also tear laundry if the fins are cracked or broken. You may be able to solve the problem temporarily by pinching off the splinters with pliers and lightly filing the plastic smooth, but this is just a stopgap measure; the agitator should be replaced. Replace a damaged agitator with a new one of the same type. To do this, unscrew the cap on top of the agitator. With the cap off, pull straight up on the agitator; it should lift off. If it doesn't move, rap its side with a hammer. If it still won't lift off, drive wedges under the bottom rim of the agitator to dislodge it. Then set the new agitator into place and replace the agitator cap.

Damage to the snubber, a padlike device sometimes located under the agitator cap, can cause the machine to vibrate excessively. The snubber may have a suspension spring in it. Lift off the agitator cap and examine the snubber. If the spring is broken, or if the pad is visibly worn, replace the entire snubber. Snubbers might also be found at the splash guard at the top of the tub, under the transmission, or as part of the water pump housing. Look around until you see it.

If the machine doesn't have a snubber, listen for noise at the suspension unit between the tub and the machine cabinet. The suspension unit has fins or pads that may need replacement. In some cases, the entire unit may have to be replaced. Another noise point is the basket support nut. Tighten the nut or, if you can't tighten it, replace it.

Sudden tub stops can be caused by a broken motor belt, but they are usually due to poor tub loading. Check to see if wet laundry is wadded around the bottom of the tub shaft, or under the basket or agitator assembly. Remove the basket or agitator in order to remove the laundry easily.

Whirlpool... | Answered on Sep 21, 2014

Your unit has an access panel, at the bottom of this panel are 2-4 screws. Remove them and the panel also, unplug the unit, with your right hand and to the right of the door, use you hand to go inside the unit toward the door latch. At the bottom of the door latch is a pull down looks like a tear drop but can only be felt. This is the door release, when you pull on this gently you should hear a click. This is the emergency door release for this unit. Good Luck

I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

Whirlpool... | Answered on Aug 05, 2014

replace them with the stainless wrapped kind and heat the room more

Whirlpool... | Answered on Jan 08, 2014

Not finding what you are looking for?
Whirlpool GHW9100L Front Load Washer Logo

253 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts


Level 3 Expert

85216 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers


Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Whirlpool Washing Machines

  • Whirlpool Washing Machines

Most Popular Question

get sud code even though not seem

  • Washing Machines