20 Most Recent Kenmore HE2t 3.7 cu. ft. Front Load Washing machine Questions & Answers


Most likely, error F 25 means that the aquasensor, the turbidity sensor of water, has failed.

Possible reasons of this error:
1) Perhaps there was a clog in the system of draining the water. Dirty water does not merge and because of this the sensor shows muddy water. It is necessary to clean the drain filter;
2) Lime or scale on the turbidity sensor. Always use high-quality washing powders or add descaling agent
3) Dirty water got into the plumbing. Drain all the water and run the wash program in hot water. The washing machine should be empty.

Kenmore HE2t 3.7... | Answered on May 15, 2017

Hi Jay , seems like there is something stuck in the drain pump . Clear the pump ( use a wet vac and open pump cap slowly to catch all that water ) . If that does work make sure you getting power from the wall. that should free those poor hostages !


Kenmore HE2t 3.7... | Answered on Dec 06, 2013

IF you take the panel off the is below the door, there is a drain plug and you should take it out. YOU will get lots of WATER. Be ready. Clean this out and try again. The issue is most likely the water solenoid valve is bad or the board that controls it is bad. You can also find the tech sheet when you look for the drain. It has all the tests that you can run.

Kenmore HE2... | Answered on May 17, 2019

There are two control boards (parts 3 and 6) shown here: http://www.searspartsdirect.com/model-number/11047571601/0582/0153200.html . Make sure to look at the Control Panel diagram. Part 3 is http://www.searspartsdirect.com/part-number/8540490/0026/110.html?modelNumber=11047571601&categoryName=Residential%20Washers&brandName=KENMORE . Part 6 is http://www.searspartsdirect.com/part-number/W10022320/0026/110.html?modelNumber=11047571601&categoryName=Residential%20Washers&brandName=KENMORE . With these part numbers, you should be able to find them online. They will be listed as Whirlpool or Whirlpool OEM parts.

If you add a comment with the problem that led you to have a technician look at the washer, I will confirm which board is which. I suspect part 6 is the B board but I'm not certain of that.

I hope this helps.

Cindy Wells

Kenmore HE2... | Answered on Apr 20, 2017

unplug--see if it resets--if not--the control box is bad--about 300 for the part

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/david_2f6e03df6c124197

Kenmore HE2... | Answered on Jan 13, 2015

sounds very like the bearing are gone i am afraid not good news its quite expensive to replace them if your machine is splitable

Kenmore HE2... | Answered on Oct 15, 2014

Appliance Repair Forums

Near top of page click on Thread "HE Error Codes"

Even blonde can do it Quick fix repair for Kenmore He2 front loading...

Search youtube for he2 washer for other help videos

Kenmore HE2... | Answered on Aug 18, 2014

Not finding what you are looking for?
Kenmore HE2t 3.7 cu. ft. Front Load Washing machine Logo

11 questions posted

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts


Level 3 Expert

5692 Answers

Harvey Mahal

Level 2 Expert

39 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

HE2 Kenmore

  • HE2 Kenmore

Most Popular Question

kenmore he2t f25 error trying ohm test

  • Washing Machines