20 Most Recent Whirlpool 24 in. ADP5966 Free-standing Dishwasher - Page 9 Questions & Answers


Try unplugging it and wait 30 seconds plug it back in and it should reset the computer

Whirlpool... | Answered on May 31, 2019


I had this problem. Fixed it but not sure what i did. I suspect it was either a temporay short, moist connection, or sensitive door latch. I shut off the circuit breaker and let stand for about a week. Perhaps it is drying. Turn back on, and the lights maybe blinking again, but press cancel button. The 2 minute drain will go on, let it drain and wait. The lights may still be blinking but wait 5-10 minutes and it may reset like mine did. You may have try this process a few times, like i did. I was playing with the door a bit too, firmly open and close. Hope this helps.

Whirlpool... | Answered on May 13, 2019


There is a sequence to reset. Firstly open the door then press heated dry normal heated dry normal within three seconds of each other

4_23_2019_6_06_58_pm.png

Whirlpool... | Answered on Apr 23, 2019


If you can fix my dishwasher I might be able to fix yours

Whirlpool... | Answered on Apr 23, 2019


I had the same problem with a Whirlpool ADP 6515, led flashes 6 times, pause and repeat.
Open the door, remove the 2 screws that hold the control panel (1 top left, 1 top right). Gently lift the control panel up and away from the door to reveal the wiring, controllers etc. My controller was a Flextronics UCB-IC-EBL-P7-M3-HE1. Look at the connectors, one of them is marked on the controller as NTC and has 2 blue wires, push down on the white plastic tab below it and disconnect it (pull it horizontally away from the controller)..
I used a multimeter on 200k range and measured the resistance by probing those 2 blue wires and the NTC temperature sensor measured about 50k ohms +/- 5k depending on the room temperature. And that is correct for that NTC. (I knew the NTC was good as I had removed it from underneath the machine previously and measured the resistance whilst holding it under the hot tap as it went from cold water to hot. It's a Negative Temperature Coefficient sensor so the resistance reduces as it gets hotter).
So problem was definitely not that.
Solution was simple, on the connector itself, just use a very small flat bladed watchmakers type screwdriver to clean the pin contact faces and then gently pinch the pins of each wire closer together so that they bites tighter onto the controller.when you reconnect it.
Refit the control panel and problem solved.
Conclusion; the contact resistance of the connector to the controller added to the total resistance of the NTC and made the dishwasher think that the water was below the safe activation of the motor cycle, e.g. it thought the water was iced up.
Job done !

Whirlpool... | Answered on Apr 17, 2019


Yes, but the bodies won't match and it will look very odd.

Whirlpool... | Answered on Apr 10, 2019


SORRY BUT WE DO NOT HAVE EAR PHONES TO HEAR IT NOR DO WE KNOW WHAT NORMAL IS OR WAS .I WOULD SUSPECT BEARING ARE GOING OUT THO

Whirlpool... | Answered on Apr 02, 2019


You reset by turning the breaker off or pulling the plug for 10 seconds.

Whirlpool... | Answered on Mar 04, 2019

Not finding what you are looking for?
Whirlpool 24 in. ADP5966 Free-standing Dishwasher Logo

209 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Mike

Level 3 Expert

4363 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Bruce Denton

Level 2 Expert

273 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Whirlpool Dishwashers

  • Whirlpool Dishwashers

Most Popular Question

electrolux dishwasher control panic

  • Dishwashers
Loading...