20 Most Recent Concord Fans 52CP6ORB Capetown Oil Rubbed Bronze Ceiling - Page 8 Questions & Answers

Spa pump motors generally run to operate spa jets and circulate water. The hot water temperature sensor is in the pump return line and automatically turns heater on and off to maintain spa water temperature.

Dryers | Answered on Oct 03, 2019

Try some wd40 or other non conductive lubricant.
If it is the glass cover for light there should be a fancy type nut in the centre. This may be frozen with rust or corrosion, again try wd40.

Dryers | Answered on Oct 03, 2019

Try cleaning the sensor strips inside the drum. Sometimes they get gummed up. Check the exhaust vent and make sure it is clean and clear of obstructions

Dryers | Answered on Oct 02, 2019

Check all housings for proper installation and tightened. A slightly loose one will cause a buzz.

Dryers | Answered on Oct 02, 2019

I don't know. please check the home's fuses or reset the electrical panel's circuit breakers.

Dryers | Answered on Oct 02, 2019

buy a long lint trap cleaner that you can run deep into the dryer. Take the lint trap out and clean all down inside dryer under the lint trap. Then clean your exhaust hose.

Dryers | Answered on Sep 30, 2019

The copper wire is just an additional ground wire. You can leave it as it is or cut it off. It will not hurt anything if you cut it off. If it were mine I would cut the additional wire off.

Dryers | Answered on Sep 30, 2019

I brought mophorn heat press and it is not heating up I change fuse and the out light doesn't turn on how can I fix can you help

Dryers | Answered on Sep 29, 2019

Check the wiring and the lamp fittings.

Dryers | Answered on Sep 28, 2019

replace remote and the receiver. It is located under the ceiling canopy cover.

Dryers | Answered on Sep 28, 2019

Most dryers are 4" tubing. If you can use rigid tubing as it does not collect as much lint as quickly.

Dryers | Answered on Sep 24, 2019

You need to have an ohmmeter. Then you need to get access to the heater terminals. Depending on the model, it could be located near the front of the dryer or back of it. UNPLUG the dryer before removing any screws. When you fid therheater element, measure the resistance between the 2 main terminals (you don't have to disconnect any wires before measuring). You should measure somewhere between 9 and 20 ohms. If that's good, then measure between 1 of the terminals and the case (ground connection) of the heater. If you measure less than 100 ohms, then you may have an internal short in the heater element. To make sure, disconnect the wires going to the heater element and re-measure. Now you should have a very hightresistance measurement, more than 100,000 ohms to infinity. If you measure less than 1000 ohms you either have a short inside the heater, or something that got inside and got burned up, producing a carbon path for the electricity.
If the heating element checks good, then look of an open thermal fuse.

Dryers | Answered on Sep 23, 2019

If its under 1 year old , it will still be under warranty. Call Samsung Service.

Dryers | Answered on Sep 23, 2019

Fixya is unable to suggest where to find the Rhine control or a compatible replacement.

Dryers | Answered on Sep 20, 2019

Not finding what you are looking for?
Concord Fans 52CP6ORB Capetown Oil Rubbed Bronze Ceiling Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Concord Fans Dryers Experts


Level 3 Expert

746 Answers

Tom Chichester

Level 3 Expert

55370 Answers


Level 2 Expert

87 Answers

Are you a Concord Fans Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Concord Fans Dryers

  • Concord Fans Dryers

Most Popular Question

capetown 52cp shut off up

  • Dryers