Top 20 Phoenix Gold XS2300 Car Audio Amplifier Questions & Answers


LPF is typically Low Pass Frequency, it puts the amp in a state where only low frequency signals will pass thru to the speakers. LPL is for Low Pass Level control, that is used on PG products that have an LPL port. Using a phone style cable and a 50k potentiometer you can control the level of the amp's output.

Phoenix Gold... | 68 views | 0 helpful votes


You have 3 sets of wire connecting to the amp (besides the rca connection), Red is power from the battery, Black is the round wire (shorter the better), lastly Blue is the remote turn on wire. Without the remote turn on, your amp will not power up regardless of the power from the battery.

RCA connectors are for your audio, it carries the noise signal to your amp from the head unit...

Phoenix Gold... | 209 views | 2 helpful votes


See manual for your amp posted here
http://download.phoenixphorum.com/Manuals/Amplifiers/XS/xs2300blk.pdf

Power is the B+ terminal, Ground is the B- terminal. The small terminal in-between them is the remote turn-on.

Phoenix Gold... | 144 views | 0 helpful votes


http://download.phoenixphorum.com/Manuals/Amplifiers/XS/xs4chan.pdf

Phoenix Gold... | 2,064 views | 11 helpful votes


Possible that the audio output section is short . remove speakers and fix in the fuse to test, if itt blows out the fault must be confirmed by opening of the amp and disconnection of the power output driver.If teh fuse then stays the fault is confirmed. replace and test the speakers in this section before connecting.

Phoenix Gold... | 98 views | 0 helpful votes


Hey there newton,

Looks to be just over 300Watts. MSRP is $220.00 but they can be had for $100.00 to $150.00

Click here for a review.

Best regards
Mike

Phoenix Gold... | 64 views | 0 helpful votes


Ok for best results.
1.make sure you agust the gain according to person prefrences.
2make sure you set the crossover on the amp.ok in your speakers the would probley sound best if you set the Low pass fillter at 50hz and the high pass fillter at 25khz (if you have one) or on your headunit

Hope this gets the results you want.

Alex

Phoenix Gold... | 82 views | 0 helpful votes


First I hope you remove the speaker wires from the speaker that come from the built in amplifire. You cannot hook the powered sub to the amp without doing that first. Then all you need to do is run speaker wire from the sub out of the box to the amp. In no way can you hook up any other part of the powered sub, but the sub itself, to the amp. If you know the wattage of the sub and the ohms then wire it to the amp correctly. Your phoenix amp will put out 125 watts x 2 at 4 ohms and 250 watts x 2 at 2 ohms and 500 watts x 1 at 4 ohms bridged. Remember, only the sub itself in the sub enclosure can be connected to the amp. Hope this helped you. Let me know if you need more help.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/mark_b53a7494531bf96d

Phoenix Gold... | 257 views | 1 helpful votes


did u try an music shop

Phoenix Gold... | 262 views | 0 helpful votes


there is something touching or shorting out..could be speaker wire inputs on the inside..if you have it crossed over you could have it backwords or you could have a short in your RCA's..

Phoenix Gold... | 134 views | 0 helpful votes


Owner's manual


Page 14.

Phoenix Gold... | 1,045 views | 2 helpful votes


Request the diagram directly from Phoenix Gold.

Phoenix Gold Car... | 51 views | 1 helpful votes


Look up the part numbers on the components themselves. I can assure you that they are readily available from places not named PG. They are made in a factory with a bunch of diffenent Brands. If simply trying to repair the knob you may be able to use another knob from different Manufacturer if it takes the same jack for wire.

Phoenix Gold Car... | 33 views | 1 helpful votes


Probably the power is not received by the heating coil, check fuse near the power cable (inside the flap on the iron bottom), or sometimes there is fuse in the power pulg of the power chord. It is rarely that the lamp is blown

Phoenix Gold Car... | 47 views | 0 helpful votes


Most mono amps now a days give you multiple terminals. The older amps were a pain trying to stuff all the wires in one set of terminals. If the amp is rated at 2 ohms mono then make sure what ever configuration of speakers your running does not go below 2 ohms using both terminals. For example do not hook a 2 ohm load to each terminal. 2 ohms period between the 2 sets of terminals.

Phoenix Gold Car... | 205 views | 0 helpful votes


To request a schematic diagram, contact Phoenix Gold directly.

Phoenix Gold Car... | 75 views | 1 helpful votes


Probably replacement of the speaker will be necessary.

Phoenix Gold Car... | 44 views | 0 helpful votes


XS4300 SPECIFICATIONS:
Output Power: 4 ohm stereo @ 12/13.8 VDC 12/35 WRMS x 4 2 ohm stereo @ 13.8 VDC 75 WRMS x 4 4 ohm bridged @ 13.8 VDC 150 WRMS x 2 Crossover Frequencies 20Hz to 20kHz(Rnet factory set at 100Hz) Crossover Slopes 24dB per Octave

Phoenix Gold Car... | 450 views | 0 helpful votes

Not finding what you are looking for?
Phoenix Gold XS2300 Car Audio Amplifier Logo

23 questions posted

Ask a Question

Usually answered in minutes!

Top Phoenix Gold Car Audio & Video Experts

Mark Skinner

Level 2 Expert

79 Answers

Jeffery Lewis
Jeffery Lewis

Level 3 Expert

329 Answers

colinjhought

Level 2 Expert

126 Answers

Are you a Phoenix Gold Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Phoenix Gold Car Audio & Video

  • Phoenix Gold Car Audio & Video

Most Popular Question

power wires 3

  • Car Audio & Video
Loading...