20 Most Recent Kyocera FS-3900DN Laser Printer - Page 6 Questions & Answers


please install drum or toner unite or clean laser unite if you are not success then chack fuser unite

Kyocera... | Answered on Aug 27, 2009


Usually a printer doesn't lie when it indicates a paper jam, if you have checked as thoroughly as possible and no paper can be found. It is possible that the paper just isn't feeding and a printer will sometimes indicate a paper jam when paper doesn't feed. But if this isn't the case and a jam is indicated as soon as you turn the printer on, one of the plastic jam sensing actuators may be broken or hung up.

Kyocera... | Answered on Aug 20, 2009


push the drum until it clicks
power off/on

Kyocera... | Answered on Jul 13, 2009


You have pulled the drum unit out of position possably after changing the waist toner ? Open the back cover, open the frunt cover and remove the developer unit, the full unit not just the toner, open the side cover where the waist toner bottle is and push the drum unit back into place until it clicks, put the dev unit back in place and close everything reboot the machine

Kyocera... | Answered on Jul 13, 2009


The fault is described correctly by tigertail - howerver this is not a chargeable repair as the 0150 fault is due to a problem at manufacture so being out of warranty does not matter.

Call the support line and you will have to pay for delivery to the repair center but repair is free and return postage is free.

0845 456 0456 Kyocera Mita

Thanks

Russ

Kyocera... | Answered on Jul 13, 2009


could be a hundred reasons, most likely is the rollers are worn try rubbing the rollers with a scouring pad which will give them a bit more friction to grab the paper with, this is only a temperary fix though!

Kyocera... | Answered on Jul 13, 2009


try chaning the quality of the envelope, some do not respons well to heat.

Kyocera... | Answered on Jun 23, 2009


Hi,

This means your conection is or should be

Parallel port no 3

check your cabling is correct

Regards
Richard.

Kyocera... | Answered on Apr 27, 2009


Try a new bottle. I've seen where the there's enough old toner clining to the sides of the bottle that prevent the sensor from seeing through it. Of course the sensor and led may be covered with old toner. Get in there with a vacuum when the machines off and clean it out.

Kyocera... | Answered on Mar 30, 2009


Try downloading the manuals from Kyocera :
http://www.kyocerasupport.co.uk/index/download_center.false.driver.FS3900DN._.EN.html#


Please take a moment to rate this solution. Thanks.

Kyocera... | Answered on Mar 19, 2009


No, after letterhead is finished load into by-pass tray and continue with the form printering

Kyocera... | Answered on Mar 14, 2009


Please leave an email and I'll sent you the manual...

Kyocera... | Answered on Mar 09, 2009


If you pull the fuser out, look at the bottom of the sliding mechanism for a bent metal tab that actuates a switch when you close the rear drawer.

They get bent pretty easily.

Kyocera... | Answered on Feb 27, 2009


Error code 7410 indicates that the drum unit is not installed correctly. This is usually caused by dirty contacts or a faulty drum unit chip. First remove the toner and developer unit, then the waste toner bottle. Unlock and remove the drum unit by depressing the catch that sits behind the waste toner bottle and pulling the unit out to the L/H side. Be very careful not to scratch the drum and avoid strong light as it is easily damaged. Clean up all contacts and refit in reverse order. Hope this helps, if not you may need to buy a new drum unit.

Kyocera... | Answered on Feb 21, 2009


Hi, just swith off printer, and open left cover.Push drum unit(with grey lever on it -just by waste toner bottle) in the printer.Switch on printer.Drum unit was out of position.
Regards

Kyocera... | Answered on Feb 06, 2009


In printer properties.

Kyocera... | Answered on Jan 28, 2009


Right click on the printer icon and choose properties. Your emulations are listed there.

Kyocera... | Answered on Jan 23, 2009

Not finding what you are looking for?
Kyocera FS-3900DN Laser Printer Logo

189 questions posted

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

FS Kyocera

  • FS Kyocera

Most Popular Question

error call service 4000 00433933

  • Office Equipment & Supplies
Loading...